FST-2802 Gigabit Ethernet Services Module
The FST-2802 is a handheld Ethernet, Fibre Channel, and IP services test
instrument designed to meet the needs of service providers for turning up and
troubleshooting these various services. The FST-2802 enables technicians to use
one test set to turn up services ranging from 10/100 Ethernet, Gigabit Ethernet,
Fibre Channel, and IP - all from a single TestPad module!
Installed Options
- 10/100
- 1G
- VLAN
- IP
- IP Traffic
Highlights
- Full line rate traffic generation with variable traffic load
characteristics to stress test 10/100/1000 Mbps Ethernet interfaces.
- Ability to test 1.0625 and 2.125 Gbps Fibre Channel services at 100% wire
speed.
- IP ping and traceroute testing for verification of network connectivity.
- Ability to perform IP throughput verification and round trip delay
testing.
- Filtering capabilities at L2 and L3 enable users to perform circuit
troubleshooting.
- Dual-port capability for Ethernet and Fibre Channel traffic generation.
- BER testing at layer 1 and layer 2 for Ethernet and Fibre Channel
circuits.
- Loopback frame generation to automatically loop the far-end test at L2 and
L3.
- Remote graphical user interface (GUI) application for remote testing via
an analog modem, Ethernet LAN, 802.11, or Bluetooth.
- Custom and preconfigured test scripts ensure that M&Ps are followed.
Applications
- Service level agreement (SLA) verification via throughput, frame loss, and
round trip delay testing for Ethernet, Fibre Channel, and IP services.
- Automated RFC-2544 conformance testing.
- Traffic testing with VLAN 802.1Q, 802.1p, DSCP, and TOS prioritization
characteristics.
- Ping and traceroute testing for verification of network connectivity.
- Simultaneous testing of two independent circuits with full line rate
traffic generation.
Key Features
- Microsoft Windows XP platform with easy-to-use GUI.
- Variety of applications such as web browser, PDF reader, and online
keyboard.
- File transfer protocol (FTP) for storage and transfer of results.
- Connectivity methods include RS-232, USB, LAN, Bluetooth, 802.11b, and
analog modem.
2310 Field Services Module
The JDSU FST-2310 TestPad is an all-in-one testing solution that performs
SONET, SDH, T-carrier, data, and circuit-switched testing to meet the varied
testing requirements of mobile technicians. Its modular architecture protects
long-term investment by providing the flexibility, scalability, and
upgradeability to support evolving test needs. Most tests performed using the
FST-2310 can be done in only a few button pushes, without the need to sift
through hidden setup menus. Additionally, because technicians need only minimal
training to use the FST-2310, testing objectives are addressed quickly and the
cost of ownership is significantly reduced.
INSTALLED OPTIONS:
Key Features:
Application-driven icons
Test application buttons are
labeled with icons that clearly depict the way the test is performed on the
circuit; for example, select the “MON/THRU” icon when performing
circuit-monitoring tests – select the “TERM” icon when performing
circuit-terminating tests. The icons and quick setup buttons enable technicians
to use the module effectively with very little training.
Simultaneous results analysis for different signal rates
Identify the source of problems quickly by using the FST-2310’s dual results
window to analyze results from different signal rates simultaneously.
Simultaneous results analysis can also be performed on different signal results
(for example, level and bit errors) allowing for easy results correlation and
quick problem identification.
Autoconfiguration
Support for autoconfiguration is
provided for all key applications. Autoconfiguration is capable of setting
different test parameters, such as framing and pattern, as well as detecting the
signal’s multiplexed composition. This enables users to reduce the time required
for test setup.Additionally, the FST-2310 has the ability to save and store up
to 10 test set configurations that can be recalled for future use.
Remote control
Remotely configure tests and analyze
results in detail using the remote control GUI option. This allows technicians
to conveniently operate the module from a remote location using the FST-2310’s
graphical user interface (GUI) on a remote PC. The remote control GUI feature
enables technicians to connect to the FST-2310 through the PCMCIA serial or
modem card to perform tests and collect test results.
Applications:
- SONET Analysis
- SDH Analysis
- DS3 Analysis
- DS1 Analysis
- DS1/DS3 Jitter analysis
- ATM Analysis
- GR-303 Protocol Link Analysis
- ISDN PRI Testing
- Signaling Analysis
- Loop-Back Applications
FST-2000 TestPad Mainframe
The FST-2000 TestPad is the user interface for the TestPad family. The
combination of a user interface and an application module represents a complete
test tool. This architecture provides TestPad users with the flexibility to
invest in additional test modules as their testing needs change, allowing them
to capitalize on an investment already made.
The FST-2000 has been designed for mobile technicians to improve the overall
installation and troubleshooting process by providing features that are enablers
for a total process improvement solution. The FST-2000 employs wireless
connectivity, along with a local Web Browser and VT100, allows for storage and
transfer of files, all of which enable field technicians to complete their jobs
more effectively.
Features:
- Remote control via Web Browser makes remote testing and technical support
straightforward
- Web Browser and VT100 emulator provide access to provisioning systems,
while
- Web Browser also allows for retrieval of information from the
Intranet/Internet
- Support of Bluetooth, RS-232, USB-compatible and 10/100BaseT interfaces
provide a choice of local connectivity to the TestPad
- Support of Ethernet, 802.11b, analog and wireless modems (CDPD, CDMA,
etc.) allow for various LAN and WAN connectivity options
- Customizable and preconfigured test scripts offer support for closeout
tests, ensuring that M&Ps are followed
- Storage and transfer of results provide ability to store files on the test
set and transfer them to computers and other network locations via file
transfer protocol (FTP)
- Non-display version offers a lower cost solution for customers that want
to rely on laptop’s display for test configuration and retrieval of results
Installed Option:
Includes:
- Acterna FST-2000 Test Pad 2000 Communication Analyzer With Option
- Acterna FST-2802 Module With Options:
- 10/100
- 1G
- VLAN
- IP
- IP Traffic
- JDSUniphase SOC-1250N5 Short Wave Length Converter
- JDSUniphase SOC-1250N5 Long Wave Length Converter
- Fiber Cables:
- SM SC-LC Duplex
- (2) MM SC-SC Duplex
- Battery Pack
- AC Adapter/Charger
- Power Cord
- Cat5 Patch Cable
- Stylus
- Strap For Unit
- User Manual On CD-ROM
- Carrying Case
- Acterna FST-2310 Module With Options
- (2) 440 To 440 Cables
- BANTAM to Dual Hook Clip
- Acterna 80-45510-01 Cable
- (2) BANTAM to BANTAM Cables
|
