Fujikura 19S SM MM Fiber Fusion Splicer
$3,849.00
Availability:
In stock
SKU
2i68
Condition: Refurbished / Calibrated
Warranty: 1 YEAR WARRANTY
Fujikura 19S SM MM Fiber Fusion Splicer
The Fujikura 19S is a low cost, fixed v-groove single fiber splicer with similar features found on the Fujikura 70S. Incorporating the proven ruggedized features pioneered by Fujikura, the 19S has added automated and enhanced user control features to increase splicing efficiency. A user programmable, automated wind protector expedites the splicing process by automatically closing to initiate the splice process, and opening upon splice completion. Fully programmable モauto open sheath clampsヤ open one or both sheath clamps, after the tensile test, to prepare the fiber for removal. A new automated モclamshell designヤ tube heater applies heat to both sides of the splice protection sleeve resulting in a faster shrink time. Ruggedness and durability are greatly enhance by a mirror-less optical system and "severe-impact resistant" monitor. An innovative transit case doubles as a built-in or mobile workstation and makes splicing easier than ever before.
Features:
Specifications:
For full Fujikura 19S Thermal Imager product specifications, please click here: Fujikura 19S
The Fujikura 19S is a low cost, fixed v-groove single fiber splicer with similar features found on the Fujikura 70S. Incorporating the proven ruggedized features pioneered by Fujikura, the 19S has added automated and enhanced user control features to increase splicing efficiency. A user programmable, automated wind protector expedites the splicing process by automatically closing to initiate the splice process, and opening upon splice completion. Fully programmable モauto open sheath clampsヤ open one or both sheath clamps, after the tensile test, to prepare the fiber for removal. A new automated モclamshell designヤ tube heater applies heat to both sides of the splice protection sleeve resulting in a faster shrink time. Ruggedness and durability are greatly enhance by a mirror-less optical system and "severe-impact resistant" monitor. An innovative transit case doubles as a built-in or mobile workstation and makes splicing easier than ever before.
Features:
- Automated and programmable wind protector
- Fully ruggedized for shock, dust and moisture
- Li-ion battery with 180 splice/heat cycles per charge
- 5 mm cleave length for splice on connector or small package needs
- Sheath clamp or fiber holder operation
- On-board training and support videos
- Internet software upgrades
- Multi-function transit case with integrated workstation
- Fiber optic network installation and repair
- FuseConnect connector installations
- Optoelectronic device manufacturing
Specifications:
Applicable Fibers | Single-mode (G.652 & G.657), Multimode (G.651), DS (G.653), NZDS (G.655) |
Cladding Diameter | 125 µm |
Coating Diameter | 100 µm to 1,000 µm |
Fiber Cleave Length | 5 to 16 mm |
Typical Average Splice Loss | 0.05 dB with SM, 0.02 dB with MM, 0.08 dB with DS, 0.08 dB with NZDS, measured by cut-back method relevant to ITU-T and IEC standards |
Splicing Time | SM FAST mode ラ 9 seconds; SM AUTO mode ラ 11 seconds; AUTO mode ラ 11 seconds |
Arc Calibration Method | Automatic, real-time and by using results of previous splice when in AUTO mode, manual arc calibration function available |
Splicing Modes | 100 preset and user programmable modes |
Splice Loss Estimate | Based upon dual camera cladding axis offset alignment data |
Storage of Splice Result | Last 2,000 results to be stored in the internal memory |
Fiber Display | X or Y, or both X and Y simultaneously. Front or rear monitor display options with automated image orientation |
Magnification | 320X for single X or Y view, or 200X for X and Y view |
Viewing Method | Dual cameras with 4.73 inch TFT color LCD monitor |
Operating Condition | 0 to 3,660 m above sea level, 0 to 95%RH and -10 to 50°C respectively |
Mechanical Proof Test | 1.96 to 2.25N |
Tube Heater | Built-in tube heater with 30 heating modes; auto-start function |
Tube Heating Time | 17 seconds with FP3 (40), 5-16 seconds with Fujikura micro sleeves |
Protection Sleeve Length | 60 mm, 40 mm, micro |
Splice/Heat Cycles with Battery | Typical 180 cycles with power save functions activated |
Electrode Life | 3,000 Arc Discharges |
Power Supply | Auto voltage selection from 100 to 240 V AC or 10 to 15 V DC with ADC-18, 14.8 V DC with BTR-09 battery |
Terminals | USB 1.1 (USB-B type) for PC communication. Mini-DIN (6-pin) for HJS-02/03 and SH-8 tube heater |
Wind Protection | Maximum wind velocity of 15 m/s. (34 mph) |
Dimensions | 146 W x 159 D x 150 H (mm) / 5.75 W x 6.25 D x 5.9 H (inches) |
Weight | 2.3 kg (5.1 lbs) with AC adapter; 2.5 kg (5.5 lbs) with battery |
For full Fujikura 19S Thermal Imager product specifications, please click here: Fujikura 19S
Fujikura 19S SingleMode MultiMode Fixed V-Groove Fiber Fusion Splicer
Includes 6 Month Fusion Splicer Care Kit (FS6MC)
- 4oz Flip Jar Of 99% Alcohol
- (50) Non-Lint Dry Wipes
- (6) Fiber Optic Wipes w/ 99% Alcohol
- 2oz Pump Fast Evaporating Mirror Spray
- (25) Camera Swabs
- (25) V-Groove Swabs
Includes US Fiber Optic USF-21C High Precision Fiber Cleaver, Hard Carrying Case & Accessories As Listed
FSM-19S FSM 19S
Fujikura 19S Fujikura19S Fusion Splicer Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
BC# 34713-L/T*
- Fujikura 19S Fiber Fusion Splicer (BC# 34713-L/T*)
- US Fiber Optic USF-21C High Precision Fiber Cleaver w/ Case
- Clauss CFS-2 Fiber Optic Stripper
- 6 Month Fusion Splicer Care Kit FS6MC:
- 4oz Flip Jar Of 99% Alcohol
- (50) Non-Lint Dry Wipes
- (6) Fiber Optic Wipes w/ 99% Alcohol
- 2oz Pump Fast Evaporating Mirror Spray
- (25) Camera Swabs
- (25) V-Groove Swabs
- Fujikura ADC-18 AC Adapter Battery Pack w/ Power Cord
- Fujikura BTR-09 Battery Pack
- DCC-18 Charge Cable
- FH-60-250 Fiber Holder Set
- FH-60-900 Fiber Holder Set
- USB PC Interface Cable
- Strap For Unit
- User Manual On CD-ROM
- Hard Carrying Case (G)
Request a Quote for