|
Siecor M90 3000 Series Fusion Splicer
The microprocessor controlled fusion splicer is used for mechanically
durable, low-loss fusing of optical fibers with long-term
stability.
Fiber Diameters
Single-mode fibers, dispersion-shifted
single-mode fibers and multimode fibers with coating diameters of up to 900 µm
can be fused. The splicer is designed for use with the standard 125 µm outside
fiber diameter (without coating). If you need to splice fibers with other
diameters, please contact the manufacturer.
Automatic Fiber
Positioning
Fiber positioning and the fusion process run automatically. This
assures uniform high quality results independent of the operator. Two mutually
independent processes for positioning and automatic splice loss determination
have been integrated into the splicer. The time tested LID system (Local
Injection and Detection) allows for accurate core-to-core positioning of the
fiber ends such that good splicing results can even be achieved with singlemode
fibers with eccentric cores. It also allows for the measurement of splice loss
at an operational wavelength of 1300 nm. If the LID system cannot be used (e.g.
with tight-buffered fibers), the completed splice is analyzed with the L-PAS
-video system (Lens Profile Alignment System), and splice loss is indicated in
dB as well.
Fiber Requirements: Single and multimode glass fiber with 125
µm glass diameter, 250 to 900 µm coating diameters
Fiber Display: High
contrast 5.5" color LCD
Magnification: Approximately 100 power
Fiber
Positioning: Fully automatic in X, Y and Z axes
Mean Splice Loss for
Identical, Standard Single-Mode Fibers:
- Multimode fiber: typ. < 0.01 dB
- Standard single-mode fiber: typ. < 0.02 dB
Tensile Test: Automatic / OFF
Splicing Programs: Preset, special and user
programs
Video Output: CCIR output (75 ohm)
Mains Power: 95 to 260 V with
automatic voltage range selection, 50 - 60 Hz, max 100 VA
External 12 V Power
Supply: 12 - 14.5 V, max. 5 A, pole reversal protected
Data Memory Capacity:
1000 splice values
Data Output: RS 232 interface with adjustable baud
rate
LID System: Wavelength: 1300 nm, temperature compensated
Attenuation
Splices: 1 to 10 dB (in steps of 0.1 dB)
Real-Time Clock: Time and date
display with battery backup
Operating Temperature: -5° C to +45° C
Storage
Temperature: -20° C to +70° C
GN Nettest TD-1000A Fiber Wizard OTDR
Specifications :
- Center Wavelength : 1310/1550nm +/- 20nm
- Max Spectral Width : < or = 20nm (Singlemode)
- Fiber TypeSingle Mode : 9/125u
- Distance Range : 1.2km; 4km; 9km; 20km; 40km; 81km; 164km
- Data Resolution : 0.313m, 0.625m, 1.25m, 2.5m, 5m, 10m, 20m
- Distance Accuracy : 0.0025% X distance +/- distance resolution
- Vertical Linearity : +/- 0.1 dB/dB to within 8 dB of the 98% noise floor
- Real Time Display Update : 2/sec pnd
- Dynamic Range : 1310nM : 30.5dB/1550nM: 27.5dB
- Measurement Range : 1320nM: 23.5dB/ 1550nM: 20.5dB
- Initial Reflective Deadzone (typ) : 3m @ 1310nM and 1550nM
- Initial Non-Reflective Deadzone (typ) : 15m @ 1310nM and 1550nM
- Display : 7 inch diagonal LCD with backlight
Options :
- Power Meter : 10dBm to -65dBm
- Light Source Modes : CW, 1kHz
& 2kHz
- Wavelength : 1310nM &
1550nM
- Power output : -10 dBm
- Stability : 0.2dB @ 8 hrs
- Connector type : Universal
Connector Interface with ST connector
- Data Storage : 1.44MB Floppy
Drive
Environmental Specifications :
- Operating Temperature : 0
ºC to 40 ºC
- Storage Temperature : -20
°C to +60 °C
- Operating Altitude : 5,000
ft
Mechanical & General Specifications :
- Size : 11.5" X 8.25" X 4.5"
- Weight : 9.0 LBS
|
