|
Successful video, data, and voice deployments require the ability to perform
sophisticated tests quickly, with simple "go/no-go" results displayed for the
technician. Sunrise Telecom’s quality test sets simplify installation, speed
deployment, and reduce cost-of-ownership, while ensuring that the qualified
network and services meet users’ expectations.
The Sunrise Telecom HTT (Home Test Toolkit) is designed specifically for
mass-market FTTN use. This innovative product provides automatic "pass/fail"
test routines for VDSL2, VDSL, HPNA networks, RF signal, Ethernet, 802.11x
wireless, copper loop fault identification, POTS, ground continuity, and in-home
wiring identification and testing.
Highlights
- Fully qualifies the home network for data, voice and video
- Identifies impairments
- Ensures connectivity
- Reduces truck rolls
- Simplifies turn up and troubleshooting
- Indicates pass/fail with configurable thresholds
Key Features
- VDSL and VDSL2 VTU-R
- HPNA Analysis
- Cable Test
- POTS
- DC Voltage and Ohm Measurements
- Ground Continuity Test
- Wireless (802.11) Analysis
- Ethernet Link Verification
- PC Utility (Bluetooth)
Benefits
- Low cost
- All-in-one test set
- Go/No-Go service verification
- Rapid installation
- Simple pass/fail display
- Easy-to-use
Specifications
Chipset
VDSL Chipset: Conexant Accelity Packet EoVDSL
CPE
HPNA Chipset: CopperGate CopperStream CG3110
Connectors (Interfaces)
VDSL / VDSL2: RJ-11 @
100W
HPNA: RJ-11 and F-81 75W (coaxial) connector
Cable Test:
RJ-45
POTS/DC/Ohm: RJ-11
Ethernet: RJ-45
Headset: 2.5 mm
jack
Speaker
VDSL2 VTU-R Features
Line Code: Discrete MultiTone
(DMT)
Standards
ITU-T G.993.1
ITU-T G.993.2,
Profile 8d and 12a
ANSI T1.424
Modem Status
Measurements
Rate
Maximum Rate
SNR
Margin
Capacity
Attenuation
Transmit
Power
Delay
Link Measurements
Counters for CRC, FEC, HEC
events
Counters for LOS, SEF, NCD, OCD
Errored
Seconds, Severely Errored Seconds, Unavailable
Seconds
Retrains
Bits/SNR per Tone: Full graphical and tabular display
Band Plan
Selection: Plan 998, Plan 997
HPNA Receiver/Analyzer
Host and Client mode: User
selectable
Auto-discover HPNA stations and MAC addresses
Auto Test between
user selected stations
Data Rate
Power
Level
Signal-to-Noise Ratio (SNR)
Transmit and
Receive Packets
Packet Loss
User configurable
Packet count and length
Test coaxial and twisted pair HPNA networks
Cable Testing
Wiremap
Wire mapping for
RJ-45 8-pin twisted pair cable
Maximum cable length: 500 ft /150
m
Displays connected, open, short, and map
Cable Loss (Coaxial
and Twisted Pair)
Test Signal: 7 and 14
MHz
Diplexer Verification
Provide estimated cable
length (Twisted Pair Only)
Cable ID (HT T-ID-5)
Connectors:
RJ-11, F-81 coaxial
Provide termination for cable
identification
Wiremap Probe (HTT-WP)
Connectors: RJ-45 and
F-81 coaxial
Uses 2 × AA batteries
Auto Shut Off: 5 minutes
POTS/Caller ID
Loop Start, DTMF dialing, Caller
ID
Talk / listen via headset, listen via speaker
DC
Voltage
Range: 0 to ± 200 Vdc
Ohm
Measurements
Range: 100O to 1 MO
Tone Generation Frequency:
570 Hz
Ground Continuity Test
Range: 0 to 10
kO
Accuracy: 2% ± 1O (0 to 1
kO)
5%
(1 kO to 10 kO)
Wireless
Detect 802.11 b/g SSID
Signal
Strength
Channel Identification
MAC Address
Identification
Detect WEP 64 and 128 bytes encryption
Ethernet
Link Status
Link Speed (10/100M, Half/Full
Duplex)
PC Utility
Bluetooth
Configurable Threshold Criteria
and result download (CSV)
| 
