Authorize.Net Secure Checkout   PayPal Logo  
Buy Now Pay Later  
Empty Image DSL / T1 / Copper / TDR Small Arrow 3M Small Arrow Parts & Accessories
 



Share
 
  Click Here
To View Our Return Policy
 
Corner Image Corner Image
 

1L138 - 3M Dynatel 1342 Far End Device II For 965DSP

3M Dynatel 1342 Far End Device II

For Use With 965DSP, 965DSP-SA and 965DSP-B Mainframes
(965DSP Mainframes Not Included In Sale!)

The 3M 1342 Far End Device II (FEDII) provides remote controlled far end testing assistance during subscriber loop testing

Includes Accessories As Listed

FED II

3M Dynatel 1342 FED 1342FED Far End Device II Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

BC# 35919



Price: $345.00 / Each


 
 
Corner Image Below Image Corner Image
Corner Image Table Image Corner Image
 
Condition Refurbished
Warranty 1 YEAR WARRANTY
Included
  • 3M Dynatel 1342 Far End Device II (BC# 35919)
  • RJ45 To Multiple Clip Cable
  • Case For Unit
 
Corner Image Table Bottom Corner Image
Back
Tab Image Description Tab Image
Product Tab Datasheet Product Tab
Side Image
Empty Image
Empty Image
Empty Image
 3M Dynatel 1342 Far End Device II

Remote controlled far end testing assistance
The perfect companion to the 3MTM Dynatel™ 965DSP Subscriber Loop Analyzer, the 3MTM 1342 Far End Device II (FEDII) provides remote controlled far end testing assistance during subscriber loop testing. Designed to enhance technician productivity, the FEDII connects to the far end on a cable pair to enable diagnostic testing to be performed from the near end controlled by the 3M Dynatel 965DSP.

Support of “auto” test function on Dynatel 965DSP, 965DSP-SA and 965DSP-B to facilitate loss measurement:
  • Insertion loss to 1.2 MHz
  • Slope
  • Loop resistance
  • Resistance balance
One technician, one test set: Pair Qualification
With a 3M Far End Device II (FEDII), one technician with a 3M™ Dynatel™ 965DSP Subscriber Loop Analyzer can perform end-to-end testing of metallic cable pairs. Commanded by the Dynatel 965DSP, the FEDII provides trace tone to verify cable pair connection, supports the 965DSP auto testing feature and qualifies loop performance up to 1.2 MHz (ADSL).
Controlled by DTMF signaling from the 965DSP, the FEDII can be commanded to remotely power-up, respond to test signaling, transmit tone on technician-selected conductors, or close relays to short the pairs in any combination. The unit can also be powered-up and commanded manually. The new FEDII may be connected in series with a working pair or bridged on to the test pair. In addition, the FEDII may be connected to two separate pairs allowing the end users to test two pairs.

Pocket accessory
Housed in a rugged, pocket-sized plastic case within a protective Cordura pouch, the 3M Far End Device features a power on/off LED and a test lead. The FED optimizes its replaceable 9V-battery life with an automatic power-down feature.

Specifications:
Size 4.7"H X 2.6"W X 0.9"D (11.9 cm X 6.6 cm X 2.3 cm)
Weight 5.6 oz. (159 g) with battery
Operating temperature 0° to +140°F (-18° to +60°C)
Storage temperature -40° to +165°F (-40° to +75°C)
Battery life 40 hours typical
Battery shelf life 2 months (installed)
Replacement battery Recommend: DuracellTM MN1604 9V
Alkaline or equivalent
Strap resistance  Less than 0.2 ohms
DC input impedance >100 megohms tip-ring-ground
AC input impedance  ~100 kohms in series with 470 pf tip-ring
Voltage rating 250 Vdc, 150 Vac
ID tone frequency 577 Hz and 1004 Hz
ID tone amplitude  8 volts peak to peak; no load typical
Transmitted tones  0 dBm ± 0.5 dBm
400 Hz to 100 kHz
0 dBm ± 1.0 dBm
100 kHz to 1.2 Mhz




For full 3M 1342 product specifications, please click here: 3M 1342
Empty Image
Empty Image
Side Image
Side Image Side Image Site Image

Copyright © 2003- AAATesters.com | Phone: 419-517-6681 Toll Free: 1-800-548-2381

Find Us On Facebook Find Us On Twitter