Acterna BAT-2700 Base Station & Air Interface

Product features

• Multiple wireless system testing: AMPS, CDMA, GSM, iDEN and TDMA
• On-site measurement of output power level and stability, frequency offset and spectrum
• Built-in antenna enables over-the-air checkof base stations
• Interference analysis tool helps to detect interfering signals in the RF environment
• Database of base stationswith full details of site locations, configuration and settings
• Integrated single platform-based solution for RF and landline testing from air interface to complement T1/E1 up to 10 Gbps optical test modules
• Intuitive and easy-to-use graphical user interface (GUI)
• Rugged construction, lightweight design and battery-powered operation
• Dual PCMCIA slots for upgrades and expanded result storage
• Automated testing procedures to minimize complexity and training costs

Application features

• Provide field technicianswith capability to maintain base stations and relieve RF experts from timeconsuming tasks
• Verify cell operabilitywith Go/NoGo checkwithout taking the cell site out of service
• Verify RF output from the base station, and monitor the RF power and spectrum
• Confirm antenna and antenna cable quality bymeasuring forward and reflected power
• Perform RF environment tests and detect interfering signals on both uplink and downlink
• Provide data indicating that faults may be present for further evaluation by RF experts
• Store and record allmeasured data including screen captures for review by RF engineering resources

Highlights

• Use cell site support team resources efficiently for all types of trouble tickets
• Troubleshoot difficult problems or issues quickly using detailed reports and screen captures
• Test under live traffic conditions without interrupting operation and cash flow
• Protect investment by verifying landline and RF interface using the same TestPad 2000ﾙ platform
• Reduce the need for shared, specialized and expensive test equipmentwith the TestPad 2000 platform and application modules

The Acterna BAT-2700 TestPad Base Station & Air Interface Test Module is a test and measurement instrument designed to boost the productivity of base station support teams.

A wireless extension module for the TestPad 2000, this rugged, lightweight handheld tester enables field technicians to run defined RF test procedures for a Go/NoGo decision ﾖ freeing RF performance engineers to focus on more critical tasks.

The Base Station & Air Interface Test Module (BAT-2700) offers a technologically advanced solution to one of network operatorsﾒ most challenging problems: How to maintain the growing numberofbase stationswithashrinking supply of skilled RF technicians.

With the BAT-2700, field technicians can easily check the performance of a cell site without disrupting revenuegenerating traffic. This easy-to-use handheld tester allows Go/NoGo checks by non-RF technicians, as well as detailed analysis by RF experts. The BAT-2700 module measures RF parameters from a base station via direct connect or air interface.

Like a multimeter for RF the BAT-2700 measures power output, spectrum and match (VSWR). It combines all this to a fast Go/NoGo decision without having to interrupt a base stationﾒs operation. By plugging in the appropriate module, users can verifywired interfaces from copper and T1/E1 up to 10 Gbit optical as well as wireless interfaces. Because the test set is battery powered there is no need to search for a power outlet on the site. Field technicians hook the BAT-2700 module into the system by the attenuated RF outlet on the base station.

When a bidirectional coupler is installed between the antenna and the base station transmitter, fix or temporary, the BAT-2700 provides more detailed checks such as automatic checking of the antennas and base station without affecting the operation.

Designed for field use, the BAT-2700 module features one-button execution ofmeasurements. All necessary preset parameters can be downloaded from a configuration database by an accessory tool. The user simply selects the base station by its location, and initiates a testwith just the push of a button. A green field indicates ﾓPASSﾔ and a red field indicates ﾓFAILﾔ.

If allmeasurements remain within set limits, a large green light indicates a ﾓPASSﾔ situation. If one or more values fall outside tolerance limits, a red light indicates a ﾓFAILﾔ situation. Arrows in the red field also point to the failing parameters. In addition, a special icon indicates if the measurement exceeds the thresholdﾒs upper limit, or if the lower limitwas not attained.

Outside the building, the field technician can analyze the RF environment. The BAT module, equipped with its own antenna, provides reliable measurements of RF signals. The technician can detect interference in the base station frequency band (downlink), as well as in the mobile phone band (uplink) due to the high sensitivity of the BAT-2700 module.

The Acterna BAT-2700 module allows you to perform multiple applications. These applications range from simple Go/NoGo check to power alignment up to detailed RF interference analysis. This tool is applicable for both an entry level to a senior engineer.

Applications
The BAT-2700 module enables field technicians to quickly verify that base stations are operating at peak performance. With user-selectable predefined tests, even novice technicians can quickly perform such previously time-consuming tasks as pinpointing interference problems, optimizing performance and completing base station final checks.

Detect presence of faults to speed up RF expertsﾒ troubleshooting
If first-levelmeasurements indicate interference trouble, the BAT-2700 module identifies the cause of the problem ﾖ such as the radio, antenna or RF environment. The BAT-2700 module also provides RF expertswith easy access to all the information they need to diagnose the source of more complex interference problems. Measurement data can be stored as a report or screen shot, uploaded to a PC, and attached to e-mails or inserted into a report, eliminating the need for manual data entry or a long verbal text and description.

Measure output power, ripple, frequency, spectrum and reflection
To measure the base station output parameters, the field technician hooks up the BAT-2700 to the base station transmitter output. Possible access points include a bidirectional coupler which is often located inside the rack, an attenuated RF output, or a coupler that can be inserted at the hatch between the RF output and antenna. When a coupler is the access point, the technician can also check the match of the RF cable and antenna

The BAT-2700measures signal power levels, power ripple, frequency and spectrum shape on the selected carriers.

The test results are continuously updated. A graph shows the current reading, average of all readings, lowest and highest reading, and a special indicator is displayed if threshold limits were exceeded.

Verify and align the output power
Like a power meter the BAT-2700 presents the transmitted power on the screen. Easy to reach and to align in large letters. Coupling losses and pre-attenuation values are compensated so that the user reads the real power sent to the antenna. A large graphic field indicates the power in relation to the rated power. The range of this field can be enlarged up to a factor of 10 to ease the alignment at the beginning.

Test the RF environment in the frequency and time domains
Testing the RF signals as they appear in the frequencydomain is one of the first tests performed on any fault find task. Normally spectrum analyzers are used for this. The BAT-2700 also shows the RF spectrum, measuring it with a fast sweeping receiver. This technique increases the dynamic range, allowing the user to detect interfering signals beside the main carrier. It also allows the user to look into the receive band, measure the noise floor and check the mobile phone transmission signals in this band. This is a passive way to check the whole receive chain, from the antenna to the receive input of the base station. The RF signals can be monitored in both the frequency and time domains. Like a zero span mode, the BAT-2700 shows also the signal strength over time. The technician can also check the burst shape or the flatness of the power roof on timed signals (figure 5). Continuous signal ripples can be detected on the RF output which are caused, for example, by a defective power supply of the base station power amplifier.

Verify the antenna match in the frequency domain
Unlike ordinary voltage standing wave ratio (VSWR) meters, the BAT-2700 can measure the antenna match in the frequencydomain. The match can be measured on individual base station carriers, and these results are shown over the frequency range. As a result, the BAT-2700 can identify errors that cannot be detected by a VSWR meter either outside or inside a base station.

The field engineer uses a bidirectional coupler to determine the ratio of the power sent to the antenna, to the power reflected by the antenna, indicating a possible mismatch.

If the mismatch value is similar across all carriers, this could indicate a frequency-independent problem, such aswater in the RF cable. On the other hand, a frequency-dependent mismatch often indicates a problem in the antenna or at a connector. Therefore, checking the match in the frequency domain helps to determine the type of problem that is occurring.

Check the noise floor and high-level signal environments
Based on a unique receiver concept, the BAT-2700measures RF levels very quickly acrossmultiple frequencies. Its sensitivity exceeds that ofmobile phones. The resolution bandwidth and power level sensitivity provide measurement capabilities unlike any spectrum analyzer.

As a result, when the BAT-2700ﾒs antenna is used, the RF spectrum appears as it does on a mobile phone. Thismeans that you can identify the noise floor on your base station area and find broadband interference or noise emitters in your frequency band.

Since the BAT-2700 also covers the mobile phoneﾒs transmitting frequency band, you can measure the noise floor on the receive path by using either the BATﾒs antenna or the base stationﾒs receive antenna. By hooking up the receive path cable to the BAT-2700, youwill see noise levels and signals on your frequency screen just as your base station receiver would see them. By checking these signals and noise levels, you can find sources of interference in the mobile frequency band that are causing problems on the receive path.

Due to this receiver concept, the BAT-2700 is also robust enough to operate in high-level signal environments such as a cell site. Unlike other spectrum analyzers, however, the BAT-2700 does not generate spurious signals nor develops intermodulation products on its own. The BAT-2700 can measure low-level carrier frequencies, and find intermodulation signals inside the base station or sources of interference even close to strong base station carriers.

Find interference within and outside the base station receive and transmit band
To detect interference, the BAT-2700 provides a special screen called ﾓWaterfallﾔ. The signals are displayed over time and their power levels are represented in different colors. Each frequency sweep adds another line on the top and moves the display down. The time of the sweep is displayed on the vertical axis. This screen makes it possible to detect interference as well as detect its characteristics over time. In this screen, the horizontal lines represent a temporary broadband interference and the vertical lines represent a narrowband interference. Bursting signals are represented as dots like the hopping traffic channel above. With the BAT-2700, screen results can be easily captured and forwarded to an RF performance engineer for further analysis.

Generate detailed reports for RF performance engineers
The BAT-2700 provides RF performance engineerswith full test information. Test results and BAT-2700 screens are stored at the press of a button. After returning to the office, a field technician can upload all the stored results and screen to a PC and attach them to e-mails or overall reports. The RF performance engineers can have immediate access to the data and can make fast, accurate decisions away from the faulty site to troubleshoot and improve the performance of a system.

Specifications

For full Acterna BAT-2700 product specifications, please click here: Acterna BAT-2700

Acterna BAT-2700 TestPad Base Station & Air Interface Test Module

To Be Used With The Acterna TTC-2000 TestPad

Includes Accessories As Listed!

BAT 2700 BAT2700 FST 2000 FST2000

Acterna BAT-2700 TestPad Base Station & Air Interface Test Module BAT2700 TestPad Base Station & Air Interface Test Module Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

• Acterna BAT-2700 TestPad Base Station & Air Interface Test Module (BC# 05242) 
• Antenna
• User Manual On CD-ROM

Having trouble viewing this file? Click this link to download