Anritsu MG3633A Synthesized Signal Generator
Condition: Refurbished / Calibrated
Warranty: 1 YEAR WARRANTY
Anritsu MG3633A Signal Generator 10 kHz to 2700 MHz
Option 03: Reference Oscillators Aging Rate after 48 hours : 5 x 10 -10/day
Option 04: Rear RF output, SMA connector
The MG3633A has excellent frequency resolution, frequency switching speed, signal purity, and a high output level, in addition to amplitude, frequency, and phase modulation functions. Also, sweep functions are provided for carrier frequency, output level, and modulation frequency so an appropriate sweep can be performed for various devices to be measured.
Also, the MG3633A has a frequency memory that can store 1000 car-rier frequencies and a function memory that stores 100 panel settings. Moreover, since the maximum output level is +17 dBm, it can be used for various local signal sources.
The MG3633A is suitable for research and development of mobile communications in the quasi-microwave band, performance evaluation, characteristics testing, and adjustment of various types of radio equipment such as digital land-based mobile communications, mobile satellite communications, satellite broadcasting, and radio LANs.
Features:
Low Noise
By using both the latest synthesizer and RF-device technologies and optical data links in the internal control circuit, the SSB phase noise has been cut to -140 dBc/Hz (CW, 1.1 GHz, offset 20 kHz). In particular, the MG3633A shows its power in measurement of narrow-band radio equipment S/N ratio and adjacent channel selectivity.
High accuracy and high-output level
Low levels of -123 dBm can be set with ±1 dB accuracy by using a high-accuracy programmable attenuator. The output level can be displayed in units of dBm, dBµV, V, mV, and µV or as a relative value (dB).
Modulation characteristics
The MG3633A has AM, FM, oM, and a combination of all three modulation functions. A DC mode is provided for FM, which makes simulation of digital transmissions for a pager possible. Also, a built-in AF oscillator with a 0.1 Hz to 100 kHz synthesizer can handle various modulations.
Quasi-microwave output
The MG3633A covers a wide range (from 10 kHz to 2700 MHz) and is suitable for research and development, as well as production of quasi-microwave band radio equipment.
Performance
Signal purity
The MG3633A has excellent spectral purity. As shown in the Fig. 1, the SSB phase noise at 1 GHz with 20 kHz signal offset is ?140 dBc/Hz. In particular, this shows its power for generating signals used for testing radio receiver selectivity, for generating high-speed clocks of A/D converters and dividers, as well as for generating standard signals for communications links.
SPECIFICATIONS:
| Form Factor | Benchtop |
| Minimum Frequency | 10 kHz |
| Maximum Frequency | 2700 MHz |
| Frequency Resolution | 0.01 Hz |
| Frequency Switching Time | 10 ms |
| Time base stability | 0.00000002 /day |
| External Frequency Reference | 10 MHz |
| Minimum Output Power | -143 dBm |
| Maximum Output Power | 23 dBm |
| Power Resolution | 0.1 dB |
| Output Accuracy | 2 dB |
| Output Level Switching Time | 25 ms |
| Output Impedance | 50 Ohm |
| Minimum Single-Side-Band Noise | -145 dBc/Hz |
| Maximum Single-Side-Band Noise | -97 dBc/Hz |
| Harmonics (noise) | -30 dBc |
| Non-harmonics (noise) | -68 dBc |
| Modulation | AM,FM,Phase |
| External Modulation Inputs(Types) | Yes |
| Sweep Modes | Linear,List,Log |
Anritsu MG3633A Synthesized Signal Generator 10 kHz to 2700 MHz Range
Installed Options:
- Option 03: Reference Oscillator
- Option 04: Rear RF Output, SMA Connector
The MG3633A has excellent frequency resolution, frequency switching speed, signal purity, and a high output level, in addition to amplitude, frequency, and phase modulation functions.
Includes Accessories As Listed
Anritsu MG3633A Signal Generator MG-3633A Signal Generator Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
BC# 11773-L/T*
- Anritsu MG3633A Synthesized Signal Generator 10 kHz to 2700 MHz (BC# 11773-L/T*) With:
- Option 03: Reference Oscillator
- Option 04: Rear RF Output, SMA Connector
- (2) BNC To BNC Cables
- Power Cord
- User Manual On CD-ROM