Netscout LinkRunner AT-2000 Auto Tester

Netscout Linkerunner AT 2000 Network Auto Tester

LinkRunner AT Provides the answers you need to quickly troubleshoot connectivity problems:

• Where does this cable or jack go?
• How is this switch port provisioned?
• Can I negotiate a Gigabit link?
• Are there 802.1x security conflicts?
• Are the DHCP and DNS servers working?
• Can I get enough power from this port?
• Can I connect to servers and the Internet with IPv4 and IPv6?
• Can I connect over copper or fiber links?
• Is this patch cable good?

In seconds, the LinkRunner AutoTest provides these answers and more on a brightly colored display that's easy to read under desks or outdoors. You can document your test results with two quick keystrokes to prove the job's done right. With a six hour battery life and rugged design, LinkRunner can work wherever and whenever you need it.

Linkrunner AT Features:

• Instant-on Operation
  • Ready to run your first test in less than three seconds
• Get answers fast
  • User-defined AutoTest performs your required set of connectivity tests in seconds, enabling you to accurately and quickly identify and solve network problems
• Verify connection at 10/100/1G over copper or 100/1G over fiber
  • Connect using copper or fiber, turn it on to see link status, connection type, signal stength and traffic.
• Nearest switch and VLAN information
  • Uses IEEE Link Layer Discovery Prtocol (LLDP) Plus the Cisco and Extreme Discovery Protocols (CDP and EDP) to display the VLAN and nearest switch model, slot and port.
• TruePower PoE Testing
  • Quickly validate PoE performance by drawing actual power up to the 802.3at standard 25.5W. Load the circuit to stress switches, cabling and patch panels, all while measuring the voltage and pairs being used. The ability to validate the TruePower delivery before installing cameras, AP's and phones ensures smooth deployment.
• 802.1x Authentication
  • Verify access to secure networks using 802.1x and MAC access Control Lists (ACL).
• Cable verification and toning
  • Check patch cables using the built-in wiremap port including pin-to-pin connection, or installed wiring for length, shorts, opens or split pairs.
• IPv4/IPv6 Ready
  • Supports both IPv4 and IPv6
• Key device and application availability
  • Instead of a ping, which is often blocked or disabled, LinkRunner performs a TCP Port open test to verify application connectivity using IPv4 and IPv6. Router, DNS and DHCP Servers are reported.
• Document results
  • Store up to 50 complete test results and download to your PC with the push of a button.
• Designed for field use
  • Six-hour Li-ion battery life, one-handed operation and a rugged design.
• Easy Upgrades
  • The mini-USB Port allows software upgrades in the field in minutes.

Functions:

Graphical Cable Wiremap and Cable Details
Finds opens, shorts, mis-wires and split pairs on non-terminated cable with a WireView Cable Identifier and built-in wiremap port.

Cable Tests
Locate cable runs with toning, port advertisement, link blinking and wiremapping with up to six cable identifiers. Toning supports both analog and digital IntelliToneﾙ modes.

Switch Information
LinkRunner AT displays critical nearest switch information including:

• Switch name and model
• IP address
• Port, slot and VLAN
• Duplex and speed (actual and advertised)
• Signal strength
• Connection MDI or MID/X
• PoE voltage and power (actual and test limits)
• Graphical representation of power on pairs

TruePower PoE Loading
Verify you are receiving the required curent and voltage up to 25.5W to power your PoE enabled devices. The LinkRunner TruePower PoE loading draws actual power to verify that your PoE enable devices will have the required power to function.

AutoTest
Verify Enterprise connectivity in seconds with AutoTest. Standardize your set of critical netowrk tests in profiles to run every time. Tests include:

• PoE (Copper Only) Class
• Link speed and duplex (actual and advertised)
• RX pair and polarity
• 802.1x authentication
• Switch name, port, VLAN, model and IP
• DHCP Auto-negotiation with subnet and DHCP server addresses
• IPv4 and IPv6 availability
• Ping and TCP port connectivity with lost and min, max and average speed

Ping and TCP Port Connectivity
Verify connectivity to key devices with ping and TCP connectivity testing. Devices automatically include a router, DNS server and DHCP server. Configure 10 additional devices to meet your requirements by URL or IPv4/IPv6 address and optional application port number.

Reflector
The LinkRunner packet reflector mode allows it to be used as a remote device during throughput tests to validate LAN and WAN throughput capabilities. LinkRunner AT supports packet reflection for:

• OptiView XG Network Analysis Tablet
• OneTouch AT Network Assistant
• EtherScope Network Assistant
• MetroScope Service Provider Assitant

Specifications:

For Full Fluke Networks LinkRunner AT-2000 product specifications, please click here: Fluke Networks LinkRunner AT-2000

Netscout LinkRunner AT-2000 Network Auto Tester

Verify connection at 10/100/1G over copper or 100/1G over fiber

Includes Carrying Case & Accessories As Listed

AT 2000 AT2000 AT-2000 LRAT-2000 LRAT 2000 LRAT2000

Netscout AT-2000 AT2000 LinkRunner Network Auto Tester Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

BC# 44396-L/T*

• Netscout LinkRunner AT-2000 (BC# 44396-L/T*)
• Ethernet Cable
• Finisar FTLF1319P1BTL Transceiver - 1310
• (2) SM LC-LC Duplex Fiber Cables
• Wireview Cable ID #2
• USB PC Interface Cable
• User Manual On CD-ROM
• Carrying Case (G)

Having trouble viewing this file? Click this link to download