Authorize.Net Secure Checkout   PayPal Logo  
Buy Now Pay Later  
Empty Image DSL / T1 / Copper / TDR Small Arrow JDSU Acterna Small Arrow HST Series Small Arrow HST-3000C Series

  Click Here
To View Our Return Policy
Corner Image Corner Image

1L34 - JDSU Acterna HST-3000C Tester w/ HST-3000 T1 / T3

JDSU Acterna HST-3000C HandHeld Consumer Services Tester

- JDSU HST-3000 SIM T1 / T3 Module (T1 testing including BERT, loopcodes, and NIU/CSU emulation)

Installed Options:
- Web Browser
- VoIP H.323 Call control
- IP Suite
- VoIP Mean Opinions Score
- VoIP SCCP Call Control
- User Scripting
- VoIP SIP Call Control
- T1 Signaling
- VoIP UNISTEM Call Control
- VoIP
- VT100 Emulation

Includes Carrying Case & Accessories As Listed

HST-3000 HST3000 HST 3000 3000

JDSU HST-3000C T1 / T3 HST3000C T1 / T3 Consumer Services Tester Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

BC# 29742-L/T* 29743-L/T*

Price: $1,595.00 / Each

Corner Image Below Image Corner Image
Corner Image Table Image Corner Image
Condition Refurbished / Calibrated
  • JDSU HST-3000C HandHeld Consumer Services Tester (BC# 29742-L/T*) With Options:
    • Web Browser
    • VoIP H.323 Call control
    • IP Suite
    • VoIP Mean opinions Score
    • PCM TIMS
    • VoIP SCCP Call Control
    • User Scripting
    • VoIP SIP Call Control
    • T1 Signaling
    • VoIP UNISTEM Call Control
    • VoIP
    • VT100 Emulation
  • JDSU HST-3000 T1/T3 Module (BC# 29743-L/T*)
  • (2) BNC Cables
  • (2) Bantam Cables
  • Ethernet Cable
  • Battery Pack
  • AC Adapter/Charger
  • Power Cord
  • User Manual On Cd-ROM
  • Case For Unit
  • Carrying Case (G)
Corner Image Table Bottom Corner Image
Tab Image Description Tab Image
Product Tab Datasheet Product Tab
Side Image
Empty Image
Empty Image
Empty Image

Acterna HST-3000 Handheld Consumer Services Tester


  • Test call types including voice, 56K, 64K, Nx56K, Nx64Kand H0 to verify correctswitch translations for inbound and outbound calls
  • Place and receive calls on T1 (primary or secondary) for NFAS configurations
  • Switch in-service D-channel to stand by D-channel for verification of Dchannel backup operation in NFAS configurations
  • Call status results provide summary of calls
  • D-channel monitoring of layer 2/layer 3 cause code messages
  • Store and print full layer 3 (Q.931) decodes

As a widely deployed service, ISDN is a key source of revenue for telecommunication service providers world-wide. This, coupled with today’s reduced budgets and smaller workforces, make it more critical than ever to ensure the timely and successful turn up and maintenance of ISDN service – the first time out. Additionally, thorough ISDN testing can prove more complex than basic physical layer and BER testing for technicians who lack the necessary training. To meet these challenges, an easy-to-use, versatile test solution is required that helps reduce failures and repeat rates while enhancing efficiency and ensuring consistent test practices.

The Acterna HST-3000 is a powerful and versatile test instrument for testing ISDN PRI service. Hand-held, rugged and easy-to-use, the HST-3000 is ideal for field use. Its modular design provides a scalable, all-in-one solution for ISDN testing, as well as thorough testing of the facilities over which it is provided.

The HST-3000 ISDN PRI option enables testing of Primary Rate ISDN circuits at both the customer site and central office. It supports call placement, receipt, D-Channel Decode analysis for 23B+D, NFAS (Non-Facility Associated Signaling), 24B and backup D channel switching. With the full range of T1 loopcodes and BERT patterns it can also test BER across any combination of channels to verify service before delivery to the customer.

Compact and rugged for field technicians, the HST-3000 can be used in all conditions, from an inside office environment to a noisy, wet outdoor span repeater. The HST-3000 also boasts automated setups and advanced features that ensure consistent adherence to service provider methods and procedures. Each HST-3000 is built to order and can easily be field-upgraded with new modules and software as application and technology needs change.

Call Verification
The HST-3000 can place, receive and monitor ISDN PRI calls on a primary or secondary T1 interface. It has the ability to place and receive single or NFASvoice, 3.1 kHz audio, 56k data, 64k data, Nx56/64k data or H0 calls. In addition, dual transmit/receive interfaces, standard on each T1 Service Interface Module (SIM), allows the HST-3000 to be deployed to test in-service to standby D-channel switching. Allmajor call controls are supported, including National, DMSand 5ESS.

For incoming calls, the HST-3000 can either prompt the user to accept or reject the call, automatically accept or reject the call, or accept and loop back the B channels. After a call has been accepted, the technician can drop the received B channel data to the speaker or headset or BERT the call. BER testing and a voice path via a handset is provided to qualify these data and voice calls, respectively. This allows technicians to access T1 physical linkmeasurements and verify switch translations prior to delivering service.

Easy-to-read result menus allow technicians to view ISDN statistics, call status, BERT results, T1 results and D-channel decodes. Technicians can also view a summary screen that presents a rapid assessment of test performance and a summary of results for the physical layer, LAPD and Q.931 results.

D-Channel Decodes Analysis
D-Channel decodes help to verify that a call is successfully established, or determine why a callwas not completed by examining the protocol cause values. The HST-3000 can monitor layer 2 (Q.921) and layer 3 (Q.931) cause code messages on the D-channel in both terminate and monitor modes. Layer 2 results give technicians the ability to check link and D-channel status, verify LAPD frames and check utilization rates. Following link establishment, layer 3 decodes allow technicians to verify such factors as call state, who made or dropped the call, why the callwas dropped, where the call is being carried (Interface ID/B-Channel) and call types.

Non-intrusive, bi-directional monitoring of in-service D-channel signaling messagesmakes troubleshooting ISDN service easier. For ISDN PRI circuits, the technician can access live D-channel lines through monitor jacks on a DSX patch panel. If the problem can not be isolated, then sectionalization can be accomplished byemulating either the TE or the NT. This enables the technician to sequentially replace each piece of premise equipment to identify the source of errors– reducing the total time to trouble resolution. Results can be displayed on-screen or stored for later retrieval and output via RS-232, USB or Ethernet connectivity standard with each base unit.

Flexible and Rugged Design
The HST’s rugged, weather resistant design and long battery life are ideally suited for use in the field. Itsmodularity allows for field upgrades to support new testing requirements. Standard Ethernet, USB and serial connections offer flexibility to easilydownload software and offload captured test data.

Easily configurable, the HST-3000 can be used by different technicianswith different responsibilities to perform a wide number of tests. The HST-3000 is easilyupgradeable with technologies and advanced options that support the changing needsof service installers.

Test the Copper, Test the Service, Improve the Process
If equipped with the Copper Testing option and a copper Service Interface Module , the HST-3000 can quickly troubleshoot the local loop for line impairments that degrade or impair T1 performance. With the HST-3000, technicians can quickly identify and locate cable impairments: shorts, grounds, opens, crosses, bridged taps, wet sections and other high resistive faults. These impairments are easy to accesswith the HST-3000’s advanced time domain reflectometer (TDR), precision digital volt/ohm meter (DVOM) and an accurate resistive fault locator (RFL) to pinpoint troubles prior to circuit installation. Copper test features are optimized for use anywhere on the local loop – at the NID, crossbox, pedestal, main distribution frame or anywhere a technician might gain access to the local loop to locate the source of trouble.

The T1 or HDSLfacility that carries the ISDN PRI service can be qualified using a number ofBERT patterns, such asQRSS, 1 in 8 and 3 in 24. The HST-3000 has an internal T1 clock signal and can also respond to in-band or out-of-band loopbackcommands, making it ideal for end-to-end or loopbackBER testing.

After the physical layer has been tested, the actual ISDN service can be tested by placing and receiving calls, which verifiesproper switch translations. The HST-3000’spre-programmed tests and customized scriptsensure that all technicians, including novice users, follow the same procedures, eliminating mistakes caused by improper test configurations or incorrect procedures.

Acterna’sTechComplete™ software (optional customized), allows the HST-3000 to improve turn-up and maintenance processesby operating with service provider’s dispatch and closeout report systems to offload stored test results for later trend analysis and coaching reports. With these features, the HST-3000 can reduce repeat rates and failures and improve overallprocess efficiency.


T1 / T3 Service Interface Module (SIM)

  • Thorough T1 testing including BERT, loopcodes, and NIU/CSU emulation
  • VT100 emulation for access to T1, HDSL, HDSL2, HDSL2- 4 wire performance statistics
  • Copper option adds in-depth copper measurements including DVOM, graphical TDR, RFA/RFL, and load coil counter
  • Lower repeat rates with automated close out tests, scripting, and pass/fail tests loaded with operator specific thresholds for methods and procedures
  • Modular hardware and software architecture allows easy upgrades and enhancements
  • T-BERD® advanced stress patterns, intelligent repeater loop codes, and BERT patterns included
  • Lightweight, rugged, water resistant, and battery powered handheld test instrument
  • NetAnalyst control of Data Network Analyzer test devices

For full JDSU HST-3000C T1 / T3 product specifications, please click here: JDSU HST-3000C T1 / T3
Empty Image
Empty Image
Side Image
Side Image Side Image Site Image

Copyright © 2003- | Phone: 419-517-6681 Toll Free: 1-800-548-2381

Find Us On Facebook Find Us On Twitter