JDSU Validator Pro-NT NT1155 Network / LAN Tester
Condition: Refurbished / Calibrated
Warranty: 1 YEAR WARRANTY
Building on the capabilities of the JDSU Validator and Validator-NT, the JDSU ValidatorPRO series of Ethernet Network Management Tools offers a complete solution to test copper and fiber Ethernet cables. The ValidatorPRO Ethernet speed certifier with integrated optical power meter and accompanying Plan-Um cable management software delivers the power to test both copper and fiber cabling, determine if cables can support Gigabit Ethernet, and perform troubleshooting for cable installations. The ValidatorPRO performs all tests offered by the Validator and Validator-NT, including speed certifying the data-carrying capabilities of copper Ethernet network cables up to 1 Gb/s by testing for noise in the network, detecting faults in the cabling wiring, and ensuring that cables can support the speed capabilities of active equipment.
To certify Ethernet speed performance of cable runs, the ValidatorPRO series of handheld testers conducts bit error rate (BER) tests by sending data packets down specified cable runs at defined data rates to check for errors at the maximum throughput of the link. The ValidatorPRO also reports on signal quality that can impact high-speed data transmission by measuring signal-to-noise ratio (SNR). Skew measurements provide the signal time delay between pairs that can impact Ethernet data transmission. The ValidatorPRO also provides continuity testing that detects opens, shorts, miswires, split pairs, reversals, and high-resistance faults while accurately measuring distance to faults and total cable length.
The ValidatorPRO includes an integrated optical power meter that measures optical power at 850/1300/1310/1490/1550 nm on multimode or single-mode fiber to address an increasing number of Ethernet networks that now include optical links.
The ValidatorPRO-NT version includes a comprehensive set of features for testing a networkâ??s active network capabilities: measure Power over Ethernet (PoE) to ensure the correct power is available on the correct pins, use port discovery to ensure the correct speed and duplex capability are available; connect at gigabit Ethernet and run ping tests to verify connectivity to IP hosts; discover network devices using Cisco Discovery Protocol (CDP) or Link Layer Discovery Protocol (LLDP), discovery and display essential information regarding functionality and configuration of 802.11 b/g/n networks.
Features:
- Measures optical power on single mode and multimode fiber
- Conducts BER testing to speed certify Ethernet data transmission speed up to 1000BASE-T (1 Gb/s)
- Measures SNR and skew to uncover impairments to electrical Ethernet data transmission
- Tests for opens, shorts, split pairs, miswires, and reversals and measures distance to opens and shortsâ??supports all copper network, telco, and coax cables
Applications:
- Certify speed capability of electrical Ethernet cable runs to support 10/100/1000 Mb/s Ethernet applications
- Ensure configuration and connectivity with active network devices
- Measure optical power and insertion loss
- Discover and display essential information regarding functionality of 802.11 b/g/n wireless devices
- Document network topology including moves, adds, and changes
Specifications:
General | |
Display |
Color back-lit FSTN liquid crystal display (LCD) |
Operating System | Linux |
Keypad | Full navigations set with alphanumeric data entry and soft-key functions |
Memory | Non-volatile memory: internal NAND flash memory Volatile memory: 128 MByte DDR2 SDRAM memory |
Languages supported (GUI) | English, French, Italian, German, Spanish, Portuguese, Korean, and Simplified Chinese |
Interfaces | - USB 2.0 host port (for external memory sticks) - Optical Power meter for 850/1300/1310/1490/1550 nm wavelengths. â??45 to +10 dBm dynamic range for 850 nm and -50 to +10 dBm for all other frequencies. ±0.20 dB accuracy. ±0.06 dB linearity. Measured in dB or dBm. Auto wavelength selection with 270, 330, 1 k, 2 kHz modulation - Wi-Fi 2.4 GHz 802.11 b/g/n standards with MIMO technology. Support 64/128-bit WEP encryption, WPA, WPA2, and CISCO CCX security |
Test Connectors | â?? 8-position shielded modular jack (data) â?? 6-position modular jack (telephone) â?? F-coax (video) Male connector w/sacrificial adapter â?? 2.5 mm universal push pull (UPP) (Fiber |
Cable Types | â?? Shielded or unshielded twisted pair network cable â?? Telephone â?? Coax â?? Single-mode and multimode fiber cable |
Cable Length | |
Maximum cable length: | 2,000 ft (600 meters) |
Maximum cable length for testing of split pairs: Up to 100 meters | (327 ft),depending upon cable type |
Cable length accuracy | ±5% (after performing both unit and cable calibration) |
Electrical | |
Power sources: | AC adapter; auto cigarette lighter power adapter; lithium-ion rechargeable, removable batteries |
Environmental | |
Operating temperature | 0 to 50°C (32 to 122°F) (normal operation, not charging battery) 0 to 45°C (32 to 113°F) (charging battery) |
Storage temperature | -20 to 60°C (â??4 to 140°F) |
Operating humidity | 10 to 85% RH, non-condensing |
Shock and Vibration minimum | 2 ft drop (free fall from stationary) on concrete |
Safety: | EN 61010-1 |
EMI/EMC | EN 61326-1:2006 |
Altitude: | 4000 m |
Agency Certifications and Compliance | |
Main and Remote units: | CE |
Battery | CE |
AC wall adapter: | CE, PSE, UL |
Auto cigarette lighter power: | CE |
Calibration | |
Traceable Calibration Period: | 2 Years |
Self-Calibration Period: | 30 days for unit calibration Perform cable calibration whenever changing cable type being measured |
Physical | |
Main Unit Size | 22.9 x 11.4 x 5.3 cm (9 x 4.5 x 1.8 in) |
Weight | 710 gm (1 lb 9 oz) with battery |
Remote | |
Size | 14.2 x 11.2 x 4.4 cm (5.6 x 4.4 x 1.8 in) |
Weight | 341 gm (12 oz) with battery |
For full JDSU NT1155 product specifications, please click here: JDSU NT1155
JDSU Validator Pro-NT NT1155 Network / LAN Cable Tester
The ValidatorPRO performs all tests offered by the Validator and Validator-NT, including speed certifying the data-carrying capabilities of copper Ethernet network cables up to 1 Gb/s by testing for noise in the network, detecting faults in the cabling wiring, and ensuring that cables can support the speed capabilities of active equipment.
The ValidatorPRO-NT version includes a comprehensive set of features for testing a network’s active network capabilities: measure Power over Ethernet (PoE) to ensure the correct power is available on the correct pins, use port discovery to ensure the correct speed and duplex capability are available
Power Meter:
- 850nm
- 1300nm
- 1310nm
- 1490nm
- 1550nm
Includes Carrying Case & Accessories As Listed
Validator-Pro NT 1155 NT-1155 Validator Pro
JDSU NT1155 NT-1155 Validator Pro-NT Network LAN Cable Tester Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
BC# 10006A-L/T* 10006B-L/T*
- JDSU NT1155 Validator Pro-NT Network LAN Tester (BC# 10006A-L/T*)
- Power Meter Wavelengths:
- 850nm
- 1300nm
- 1310nm
- 1490nm
- 1550nm
- Power Meter Wavelengths:
- JDSU NT1025 Validator Pro-NT Remote (BC# 10006B-L/T*)
- JDSU Remote Adapters #1-8
- (2) RJ45 To Multiple Clip Cables
- (2) TP74 Sacrificial cables
- (2) Ethernet Cables
- (2) RJ11 Patch Cables
- (2) AC Adapter/Charger
- DC Car Charger
- (2) Power Cords
- USB PC Interface Cable
- Validator Pro Instruments on Thumb Drive
- User Manual On CD-ROM
- Carrying Case w/ Strap