Authorize.Net Secure Checkout   PayPal Logo  
Buy Now Pay Later  
Empty Image Fiber Optic Test Small Arrow Westover Small Arrow HD1 Series
 



Share
 
  Click Here
To View Our Return Policy
 
Corner Image Corner Image
 

3W04 - EXFO HD1 Fiber Inspection System FBP-HD1

EXFO FBP-HD1 Hand-Held Fiber Inspection Display Unit With
EXFO FBP 200X Probe Microscope

Inspect installed connectors that are located inside hardware devices without accessing the "backside" of patch panels.

Includes Hard Carrying Case & Accessories As Listed

FBP HD1 HD 1 HD-1

EXFO FBP-HD1 FBPHD1 Fiber Inspection System Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

BC# 13919




 
 
Corner Image Below Image Corner Image
Corner Image Table Image Corner Image
 
Condition Refurbished
Warranty 90 Day Exchange
Included
  • Westover FBP-HD1 Hand-Held Display Unit (BC# 13919)
  • Westover FBP Probe Microscope
  • Westover FBPT-U25M Connector
  • AC Adapter/Charger
  • Power Cord
  • Hard Carrying Case
 
Corner Image Table Bottom Corner Image
Back
Tab Image Description Tab Image
Product Tab Datasheet Product Tab
Side Image
Empty Image
Empty Image
Empty Image

The Westover Scientific Video Inspection Probe is a portable, video microscope used to inspect fiber optic terminations. More specifically, the FBP is used to inspect installed connectors that are located inside hardware devices or in the "backside" of patch panels. It eliminates the need to access the backside of patch panels or disassemble hardware devices prior to inspection.

Patch Panels: Many patch panels feature a design wherein one connector is easily inspected (front), but the other is difficult to access (back). Inspecting the connector on the front side of the panel is commonly performed using a simple fiber inspection microscope. However, the backside connectors are not as easily inspected with traditional microscopes, thus requiring time consuming troubleshooting. The FBP system combines with Westover's line of "Cleaning Sticks" produce a fast and effective means for installing, troubleshooting, or maintaining fiber optic patch panels.

Hardware Devices and Test Equipment: Most hardware devices feature connectors, at the faceplace of a "box", that lead to the back-plane circuitry. These connectors are very difficult to access since they are built into the device's enclosure. If a contaminates jumper is inserted, the termination inside the divice can become contaminated and contribure to signal loss. Many test equipment designs feature the same type of "back plane" fiber wherein a critical fiber termination lies just inside a piece of hardware. The FBP "Probe" used in conjuntion with Westover's line of "Cleaning Sitcks" can be used to ensure that the termination inside is clean.

Mil-Aero Connectors:

Most Mil-Aero connectors are based on multiple fiber plugs that embody "Termini" ferrules. Typically, one end of the connector contains multiple "pins" and the other contains multipler "sockets". In either cas, you cannot inspect the terminations with a traditional microscope because you're not able to "look" down inside the sockets. Using the FBP "Probe", you are able to access the fiber endfaces, and inspect these connectors fully assembled.

Cable Assemblies:

In addition to inspecting backside connectors through bulkhead adapters, the FBP is available with an adapter tip for inspecting patch cables and cable assemblies.

HD1 Hand-Held Display

Bright, hight contrast 2.5" TFT active matric LCD Display. The probe's hight magnification projects a 530-micron field onto the LCD display. The Auto-Shutoff Interval switch can be set to one of three settings: 10 sec., 30 sec., or Infinity. Pressing the On/Off switch will turn the LCD display On for the set interval time. Pushing the switch again, turns Off the display.

Battery Power and Recharge

The display utilizes a NiMH rechargable battery pack. From a full charge, the system can operate continuously for approximately 3 hours. You can ectend the battery life by using one of the two display's Auto-Shutoff Interval settings. The system's "Low Battery" indicator signals when the battery runs low. (Approximately 15 minutes before automatic shutdown. After this time, the battery must be recharged.) Use external power (AC power adapter) to charge the battery pack. Typical battery charging time is approximately 2-3 hours.

AC Power

Using the AC power adapter has the following advantages:

  • Saves internal battery power for portable operation later.
  • Charges internal battery pack.
  • Allows extended operation.

The two LED's on the front of the Hand-Held display, indicates the display's AC Power and Battery Power status.


For full EXFO HD1 product specifications, please click here: EXFO HD1

Empty Image
Empty Image
Side Image
Side Image Side Image Site Image

Copyright 2003- AAATesters.com | Phone: 419-517-6681 Toll Free: 1-800-548-2381

Find Us On Facebook Find Us On Twitter