Fluke 97 Auto Scopemeter Dual Trace 50 MHz Handheld Oscilloscope

Fluke 97 Auto Scopemeter

Your Fluke 97/Auto ScopeMeter combines the capabillities of a dual-trace, digital-storage oscilloscope with teh versatility of a digital multimeter. This combination allows you to analyze and compare complex waveforms, read voltage levels, or simply measure resistances.

ScopeMeter features include:
- Dual Trace, 50-MHz Bandwidth Scope
- 25 million samples-per-second, 40 ns glitch capture capability
- 3000 Count Digital Multimeter (DMM)
- Menu-Driven Interface for easy operation.
- Storage for 10 front panel setups (Meter and Scope Modes).
- Digital starage for eight waveforms.
- Simultaneous display of four waveforms (any combination of live and stored) allows for useful comparisons.
- Autoset configures ScopeMeter to select the best voltage and time base settings for a meaningful display.
- Undo featrue allows you to step back through the 10 most recent key presses.
- true portability and three source choices allow for testing in real-life environments.

Specifications
Multimeter
DC Volt	Ranges: 300 mV, 3V, 30V and 300V Accuracy: ±0.5% ±5 counts
AC Volt	Ranges: 300 mV, 3V, 30V and 250V Accuracy: ±1% ±10 coutns, 50 Hz to 50 Hz ±2% ±15 coutns, 20 Hz to 20 kHz ±3% ±20 coutns, 5Hz to 1 MHz additonal error ±1% ±1 kHz
For <10Hz with 10:1 probe or >100 Hz direct (1:1 probe), use function Vrms AC + V DC. The 10:1 accessory probe increases the ranges by a factor of 10. To create more accurate measurements on ac, or on dc with a large ac component, the time base often can be optimized by pressing "auto-set" or by changing the settign accessed by pressing "Time"
mV DC	Ranges: 300 mV and 3V Accuracy: ±0.5% ±5 counts This range has a low-pass filter with a bandwidth of 5 kHz.
Ω Ohm Ranges:	Ranges: 300Ω, 3kΩ, 30kΩ, 300 kΩ, 3 MΩ and 30MΩ Accuracty: ±0.5% ±5 counts Range: 30Ω Accuracty: ±2.4% ±25 counts
Diode	Measuring Current: 0.5mA Maximum Voltage: 4V
If Output Voltage is higher than 2.8V, OL (OverLoad) is displayed.
Display Modes
Frequency	The Frequency can be displayed withing the following parameters: Range: 1 Hz...5MHz Accuracy: ±0.5% Resolution: 4 Digits
Trace DISP	The display trace can be switched off.
Duty%+, Duty%- Relative on-to-off time of a varying input can be displayed as a percentage.	Range: from <2.0% to >98.0% for signal amplitudes >10% of the input voltage range. Resolution: 0.1% Accuracy (logic or pulse waveforms): within ±0.5% Accuracy (sine or triangle waveforms): within ±1% + ((Voltage Range/RMS Input Voltage) x 1%)
%/Delta	Displays the difference after 0% or % is pressed.
Scaling	0% and 100% can be set, creating an a + bx computed reading where a and b are the 0 and 100% values, respectively, and x is the measured value.
Volt Match	Results can be displayed in dBV, dBm, dBW, or Audio Watt. The assumed load resistance can be chosen from: 1,2,4,8,16,50,60,75,93,110,125,135,150,200,250,300,500,600,800,900,1000,1200 Ω, depending on teh display mode.
Record	In meter mode, the actual value is displayed simultaneously with the maximum, average, and minimum values.
Tough Hold Feature	Can be activated by pressing "Hold Run"
Oscilloscope
Vertical System
Deflection Factor	1mV to 100V per division in 1-2-5 sequence, for time base 60s/division to 1ms/division. This can be expanded by a factor of 10 witht eh 10:1 accessory probe.
Vertical Resolution	8 bits, 25 levels per division
DC Accuracy	±2%
Rise Time	Vertical amplifier response limits the rise time to 7ns. For time base settigns slower than 200ns teh rise time is smaller than the sample distance, so the measured rise time is unreliable if it is smaller than (2xs/div)/25
Bandwidth	With 10:1 prove only:> MHZ (-3dB)
Nonlinearity	Including analing to digital converter, which will have no missing codes and is monotonic: ±)2% ± 1 digit)
Move Control Range	From +4 divisions to -4 divisions
DC Balance	Base line is automatically readjusted after switching the attenuator or ac/dc/ground
MIN/MAX	Acquisition mode at 1 ms per division or slower on Channel A only. Pulse width for 100% probability of detection is 40ns.
Average	The running average can be set to 256 maximum. In Roll Mode, the average is fixed at 10.
Zoom	Expand or contract view centered around the 4th division, withing teh limits of the time base and teh maximum dleay.
Horizontal System
Range:	5s to 10ns per division with triggered start. The roll mode is active from 60s to 10s Single shots are possible from 5s to 100 ns per division
For tiem base settings faster than 1ms, an automatic interpolation takes place. The useful band-width is about 6MHz. For time base settings of 50ms or slower, the channels are chopped. for time base settigns of 20ms or faster, teh channels are alterneated. Channel A is dipslayed first and, after a second trigger pulse, Channel B is diplayed second.
ACCURACY:	Accuracy is ±0.1% 1 LSB
Sample Frequency	Dependent on time base: 25/sec-per-div) Hz (maximum 25 MHz) in Min/Max: 25 MHz
Record Length	512 samples calibrated for 25 samples per division.
Capture	Allows selection of a record length of 10 or 20 divisions
Move Control	From +4 divisions to -16.5 divisions.
A Versus B	Channel A is displayed along the vertical axis. The time base is set manually.
Trigger
Internal Sensitivity	For frequencies lower than 10MHz: <0.8 div Extra amplification in the vertical system allows for 2 mV and 1 mV per division for the input signal, but not for the trigger. Therefore, sensitivity at 2mV adn 1 mV decreases by a factor of 5.
Level Range	From +4 division to -4 divisions.
External	TTL Compatible. Selectable for 0.2V or 2V. Trigger level is indicated on the screen.
Delay Range	Time Delay: -20 to +640 divisions Events: 1 to 1023 N_CYCLE: trigger frequency divided by N (2 to 255.)
Waevform Memories	For waveform storage, eight extra memories are avialable. The memories can be cleared all together. Each memory contains 412 words for waveform and the setup belonging to this waveform.

Fluke 97/Auto ScopeMeter, Dual Trace, 50-MHz Bandwidth HandHeld Oscilloscope

Simultaneous display of four waveforms (any combination of live and stored) allows for useful comparisons.

Autoset configures ScopeMeter to select the best voltage and time base settings for a meaningful display.

Includes Carrying Case & Accessories As Listed

Fluke 97 Auto Scopemeter 97-Scopemeter Handheld Oscilloscope Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

 

BC# 44137-L/T*

• Fluke 97/Auto ScopeMeter 50MHz Oscilloscope (BC# 44137-L/T*)
• (3) Fluke Ground Leads
• (4) Fluke Test Probes
• (4) Fluke Alligator Clips
• (1) Fluke BNC Clip Cable
• (2) Coax to BNC Cables
• Fluke Inductive Pickup
• AC Adapter/Charger
  
• Hard Carrying Case

Having trouble viewing this file? Click this link to download