These three-phase power quality meters help you locate, predict, prevent and troubleshoot problems in power distribution systems. These easy-to-use power quality tools are a ﾓmust haveﾔ for any person who maintains or troubleshoots three phase power. The new IEC Class A standards for flicker and power quality are built right in to take the guess work out of power monitoring.
Applications
Frontline troubleshooting ﾖ quickly diagnose problems on-screen to get your operation back online
Predictive maintenance ﾖ detect and prevent power quality issues before they cause downtime
Quality of service compliance ﾖ validate incoming power quality at the service entrance
Long-term analysis ﾖ uncover hard-to-find or intermittent issues
Load studies ﾖ verify electrical system capacity before adding loads
Energy assessments ﾖ quantify energy consumption before and after improvements to justify energy saving devices
Faetures:
Troubleshoot real-time: Analyze the trends using the cursors and zoom toolsﾗeven while background recording continues
Highest safety rating in the industry: 600 V Cat IV/1000 V CAT III rated for use at the service entrance
Automatic transient mode: Captures 200 kHz waveform data on all phases simultaneously: Up to 6 kV
Fully Class A compliant: Conduct tests according to the stringent international IEC 61000-4-30 Class A standard
Measure all three phases and neutral: With included four current probes
AutoTrend: Every measurement you see is always automatically recorded, without any setup
System-monitor: Up to seven power quality parameters on one screen according to EN50160 power quality standard
Inrush mode: For troubleshooting nuisance circuit breaker tripping
View graphs and generate reports: With included analysis software
Logger function: Configure for any test condition with memory for over 400 parameters at user defined intervals
Mains signaling: Measure interference from ripple control signals at specific frequencies
Battery Life: Seven hours operating time per charge on NiMH battery pack
Warranty: Rugged, handheld troubleshooter with 90 Day warranty
Technical Data
Inputs
Number:
4 voltage and current (3 phases + neutral)
Maximum voltage:
1000 Vrms (6 kV peak)
Maximum sampling speed:
200 kS/s on each channel simultaneously
Volt/Amps/Hertz
Vrms (AC + DC)
Measurement range:
1 ... 1000 V
Accuracy:
0.1% of Vnom
Vpeak
Measurement range:
1 ... 1400 V
Accuracy:
5% of Vnom
Crest factor, voltage
Measurement range:
1.0 ... > 2.8
Accuracy:
±5%
Arms (AC + DC)
Measurement range:
0 ... 20 kA
Accuracy:
±0.5% ± 5 counts
Apeak
Measurement range:
0 ... 5.5 kA
Accuracy:
5%
Crest factor, A
Measurement range:
1 ... 10
Accuracy:
±5%
Hz 50 Hz nominal
Measurement range:
40 ... 70 Hz
Accuracy:
±0.01 Hz
Dips and swells
Vrms (AC+DC) ²
Measurement range:
0.0% ﾅ 100% of Vnom
Accuracy:
±0.2% of nominal voltage
Arms (AC+DC) ²
Measurement range:
0 ... 20 kA ?
Accuracy:
±1% ± 5 counts
Harmonics
Harmonic (interharmonic) (n)
Measurement range:
DC, 1..50; (Off, 1..49) measured according to IEC 61000-4-7
Vrms
Measurement range:
0.0 ﾅ 1000 V
Accuracy:
±0.05% of nominal voltage
Arms
Measurement range:
0.0 ﾅ 4000 mV x clamp scaling
Accuracy:
±5% ± 5 counts
Watts
Measurement range:
Depends on clamp scaling and voltage
Accuracy:
±5% ± n x 2% or reading, ± 10 counts
DC voltage
Measurement range:
0.0 ﾅ 1000 V
Accuracy:
±0.2% of nominal voltage
THD
Measurement range:
0.0 ﾅ 100.0%
Accuracy:
±2.5% V and A (± 5% Watt)
Hz
Measurement range:
0 ﾅ 3500 Hz
Accuracy:
± 1 Hz
Phase angle
Measurement range:
-360º ... +360º
Accuracy:
± n × 1.5º
Power and energy
Watt, VA, VAR
Measurement range:
1.0 ﾅ 20.00 MVA¹
Accuracy:
±1% ± counts
kWh, kVAh, kVARh
Measurement range:
00.00 ﾅ200.0 GVAh¹
Accuracy:
± 1.5% ± 10 counts
Power Factor/ Cos ? / DPF
Measurement range:
0ﾅ1
Accuracy:
± 0.03
Flicker
Pst (1 min), Pst, Plt, PF5
Measurement range:
0.00 ﾅ 20.00
Accuracy:
±5%
Unbalance
Volts
Measurement range:
0.0 ﾅ 5.0%
Accuracy:
±0.5%
Current
Measurement range:
0.0 ﾅ 20%
Accuracy:
± 1%
Transient Capture
Volts
Measurement range:
±6000 V
Accuracy:
±2.5% of Vrms
Minimum detect duration
5 µs (200kS/s sampling)
Inrush mode
Arms (AC+DC)
Measurement range:
0.000 ﾅ 20.00 kA¹
Accuracy:
±1% of meas ± 5 counts
Inrush duration (selectable)
Measurement range:
7.5 s ... 30 min
Accuracy:
±20 ms (Fnom = 50 Hz)
Autotrend recording
Sampling:
5 readings/sec continuous sampling per channel
Memory:
1800 min, max and avg points for each reading
Recording time:
Up to 450 days
Zoom:
Up to 12x horizontal zoom
Memory
Screens & data:
50, shared memory divided between logging, screens and data sets
Notes
¹
Depending on clamp scaling
?²
Value is measured over 1 cycle, commencing at a fundamental zero crossing, and refreshed each half-cycle
FLUKE 196B
Features & Applications:
The Fluke 196/003 ScopeMeter high-performance oscilloscope offers specifications usually found on top-end bench instruments. With up to 100 MHz bandwidth and 1 GS/s real-time sampling and a deep memory of 27,500 points per input, it's ideal for engineers who need the full capabilities of a high-performance oscilloscope in a handheld, battery-powered instrument.
Features:
Dual-input ﾖ 100 MHz bandwidth
Up to 1 GS/s real time sampling per input
Digital Persistence for analyzing complex dynamic waveforms like on an analog scope (190)
Large, high resolution color or monochrome screen
Connect and view automatic triggering and a full range of manual trigger modes
Fast display update rate for seeing dynamic behavior instantaneously
Automatic capture and replay of 100 screens
27,500 points per input record length using ScopeRecord mode
TrendPlot paperless chart recorder for trend analysis up to 22 days
UP to 1000 V independently floating isolated inputs
