Fluke Networks CertiFiber Remote MM Fiber Optic Intelligent Far End Device

The CertiFiber Remote

The CertiFiber Remote is an active and intelligent far-end device that works with the CertiFiber main unit to verify optical-cable transmission quality. All information is processed and transferred to the main unit. Both units provide a consistent, calibrated light source that increases the ease and effectiveness of fiberoptic testing.

CertiFiber Remote is designed to provide a consistent, calibrated light source for effectively measuring signal loss in fiberoptic cables. The light can be transmitted continuously or modulated: When testing loss, use CertiFiber to function as a continuous-wave (CW) light source; when identifying fiber cables with a tone locator, use the 2-KHz modulated mode.

To use the calibrated light source in the CertiFiber Remote for loss testing or fiber identification, take these steps:
1. Press and hold the CertiFiber RemoteÕs Battery button.
2. The RX1 and/or TX2 LEDs slowly flash five times as the unit performs its battery test.
3. The Wavelength LED then blinks rapidly until the Battery button is released.
4. The unit steadily lights the Wavelength LED to indicate that it is ready to provude a consistent light source for the currently selected wavelength.
5. Press and hold the Battery button if you want to switch to the other wavelength.
6. Press the Battery b

The CertiFiber Remote has four LED indicators:
RX1 PASS/FAIL	Red Green	Fiber 1 has failed Fiber 1 has passed
TX2 PASS/FAIL	Red Green	Fiber 2 has failed Fiber 2 has passed
850nm*	Green	CertiFiber Remote is transmitting at 850nm
1300nm*	Green	CertiFiber Remote is transmitting at 1300nm
* Press and hold the Battery button.
The LEDs also show the results of a battery test (which you run by pressing the Battery button):
RX1 and TX2 LEDs	Red	Low Battery < 10%
TX2 LED	Red	Battery 10 to 25%
RX1 LED	Green	Battery 25% to 75%
RX1 and TX2 LEDs	Green	Good Battery > 75%
RX1 and TX2 LEDs*	Yellow	Part 1 of Two Way Autotest completed
*Switch fiber connectors: RX2 to TX1, TX1 to RX2, RX1 to TX2, TX2 to RX1.

THE KEYPAD
ON/OFF (CertiFiber Remote) When you turn it on, CertiFiber Remote will flash the LCD power-up sequence. To save battery power, CertiFiber Remote will turn off automatically after 30 minutes without activity

Battery
(CertiFiber Remote) CertiFiber Remote has a battery-level indicator that allows you to check the battery if CertiFiber Remote is not connected to the CertiFiber main unit. Press the Battery button to illuminate the RX1 and TX2 LEDs on the CertiFiber Remote unit. If both LEDs blink red, the batteries are low and should be replaced. If the LEDs blink green, the remote unitÕs batteries are good and testing can proceed.

 CertiFiber Remote requires three AA alkaline batteries. If CertiFiber and CertiFiber Remote will be stored for more than one month, the batteries should be removed.

Fluke Networks Multimode 850 / 1300nm CertiFiber Remote

The CertiFiber Remote is an active and intelligent far-end device that works with the CertiFiber main unit to verify optical-cable transmission quality.
(Fluke Networks CertiFiber Main Unit Not Included)

Includes Carrying Case & Accessories As Listed

Fluke Networks CertiFiber Remote Certi-Fiber MM Fiber Far End Remote Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

 

BC# 42950-L/T*

• Fluke Networks CertiFiber Multimode Remote (BC# 42950-L/T*)
  • MM Source:
    • 850nm
    • 1300nm