GreenLee Progressive 620 Alarm Circuit Continuity / Discontinuity Tester w/ 200EP-G Tone Probe
Condition: Refurbished
Warranty: 1 YEAR WARRANTY
Shipping: USA & Worldwide
- GreenLee 620 Toner Continuity/Discontinuity Tester (BC# 9121B-L/T*)
- GreenLee 200EP-G Tone Probe (BC# 9121A-L/T*)
- Carrying Case
GreenLee / Progressive Electronics 620 Toner
Key Features:
• Operation
• Battery Test
• Sending Tone to Identify Wires
• Testing Switches Using the Tone Function
• Testing Switches Using the Continuity/Discontinuity Function
• Testing Telephone Circuits • Maintenance
General
The Model 620 is a hand held combination tone generator and continuity/discontinuity tester designed for use by security and alarm installation and service technicians.
The Model 620 is constructed of high impact ABS plastic, measures 4 x 23 ⁄ 8 x 1" and weighs 6 oz. with standard 9 volt battery (not included). The unit is equipped with red and black test leads with alligator clips and protective boots in addition to the snag proof RJ-11 modular plug for testing and toning telephone circuits. A six position slide switch and recessed “RESET” button control operations. A high output speaker indicates results in the continuity/discontinuity test functions.
The Model 620 is equipped with a magnetic backing for easy mounting to the control panel door or cabinet.
The “TONE” position is used to send tone over wire pairs or single conductors and to test alarm switches.
The “N.O.” position is used to test Normally Open alarm switches for continuity.
The “N.O. LATCH” position is used to test Normally Open alarm switches for continuity with the Captive feature.
The “N.C.” position is used to test Normally Closed alarm switches for discontinuity.
The “N.C. LATCH” position is used to test Normally Closed alarm switches for discontinuity with the Captive feature.
The “RESET” button is used in conjunction with the “N.O. LATCH” and “N.C. LATCH” testing features.
GreenLee 200EP-G Tone Probe
200EP-G Tone Probe
with Adjustable Volume, Visual Signal Indicator, Headset Jack, Handset Connection Tab
The 200B-G and 200EP-G Tone Probes, when used in conjunction with any Greenlee tone generator, are designed to identify and trace wires or cables within a group without damaging the insulation.
Features:
- Resistive plastic carbon-fiber tip to prevent accidental shorts when probing wires
- Adjustable volume sensitivity control
- Battery compartment
- Recessed terminal ports for handset connection
- Spring-loaded ON/OFF/flashlight* button
- LED*
- High power flashlight*
- Headset jack (acoustically protected)*
* 200EP-G only.
Safety
Safety is essential in the use and maintenance of Greenlee tools and equipment. This instruction manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of this tool. Observe all of the safety information provided.
Specifications:
Electrical | |
Gain (nominal): | 30 dB |
Input Impedance (nominal): | 100 MΩ |
Probe Tip Resistance (min): | Metal Tip: 0 Ω Plastic Tip: 300 Ω |
Headset: | 3.5 mm stereo plug; 8 ohms minimum |
Battery: | One 9 VDC (NEDA 1604, JIS 006P, or IEC 6LR61) |
Battery Life (nominal): | 50 Hours |
Physical | |
Length: | 231 mm (9.0”) |
Width: | 55 mm (2.2”) |
Depth: | 28 mm (1.1”) |
Weight: | 145 g (5.2 oz) |
Operating/Storage Conditions | Temperature: 0 °C to 50 °C (32 °F to 122 °F) |