JDSU HST-3000C CUADSL2-TX E1/Datacom & Ethernet

Improving the installation, maintenance and troubleshooting of DSL services
With a market primed for broadband, operators are rapidly deploying DSL in their networks to deliver multimedia services over the existing copper wire in the local loop. Traditionally, one set of technicians performed individualized tests that qualified the copper while another set conducted DSL services testing and verification. In todayﾒs market, however, operators can no longer afford the time, capital expense, and labor costs to conduct tests separately and incrementally. Furthermore, test solutions must generate results that have a strategic impact throughout an operatorﾒs entire organization. This may include building customer loyalty by locating and fixing problems quickly, improving profitability by performing more tests with less staff, or leveraging workforce productivity by automating processes, methods, and procedures.

The Acterna HST-3000 is a modular handheld tester that can be built to order, to test the copper, test the DSL service and improve the process. Technicians use the HST-3000 copper base instrumentand the copper service interface module (SIM) to qualify, maintain, and troubleshoot the local loop. This same base instrument, with a second SIM that tests both ADSL and the copper, enables one technician to perform tests thatwere previously conducted by two technicians using different equipment.

For those technicians who only need to test ADSL, the instrument can be configured for ADSL functionality only. Any HST-3000 module equipped to perform ADSL service tests can also verify ISP and Internet connectivity with the Acterna Advanced IP Suite software option. With the HST-3000 minimize the time and reduce the capital expense and labor cost associated with ADSL and copper testing.

Highlights

• A combined tester for Copper and DSL testing
• Lower repeat rates with automated close out tests, scripting/pass-fail tests, and back office integration
• Modular hardware and software architecture is flexible and easily upgraded
• Laptop/PC integration via RS-232, USB, or wireless for easy results transfer
• Intuitive, easy-to-use GUI, lightweight, rugged and water resistant

Instrument Interface Specifications

• Dual TIP/RING and Ground POTS/Copper: Color-coded, shrouded 2mm ﾓmini-bananaﾔ jacks
• ADSL: 8-pin modular
• 10/100 BT Ethernet jack: 8-pin modular
• Serial port: DB9 female via cable (DCE)
• USB Host
• USB Device
• Bluetooth short-range wireless

ADSL Standards

• ANSI T1.413
• ITU G.992.
• 1 Annex A
• ADSL over POTS
• (G.DMT)
• G.992.2 (G.Lite)
• Cisco CAP

General Specifications

• Ruggedness: Survives 3-ft drop to concrete on all sides
• Water-resistance: Splash proof: may be used in heavy rain
• Language: English
• Keypad: Typical 12-button keyboard

Physical Specifications

• Size (H x W x D): 9.5 x 4.5 x 2.75 in
• Weight: 2.7 lb with battery
• Operating temperature: 22°F to 122°F
• Storage temperature: ﾖ40°F to 150°F
• Battery life: 10 hrs. typical usage
• Charging time: 7 hours from full discharge to full charge
• Operating humidity: 10% to 80% relative humidity
• Storage humidity: 10% to 95% relative humidity
• Display: 1/4 VGA monochrome transflective, 3.8-in diagonal (readable in direct sunlight)

SIM CUADSL2-TX ANX A Module

The HSTﾒs copper testing features allow quick turn-up and troubleshooting of the services provided over copper. This includes testing with DVOM, opens, power (Mains) influence (PI), noise, balance, time domain reflectometer (TDR), resistive fault locate (RFL), load coil detect, loss, wideband transmission impairment measurement set (WBTIMS), caller ID, and POTS dialer.

The HST provides process customization through on-board auto tests and allows workflow improvements via connectivity to craft access terminals and back-office systems.

The copper testing features include the following:

• Measuring AC and DC voltage, current, and resistance
• Measuring to opens (length of cable)
• Measuring balance, noise, and power (Mains) influence (PI)
• Locating cable faults with the TDR or RFL
• Detecting load coils
• Measuring loop loss (voiceband) including receiving and sending tones; transmission impairment testing (noise, SNR, return loss)
• Voice service and caller ID (CLID) testing
• WBTIMS and WB2 TIMS testing including sending/ receiving tones; measuring wideband, impulse, and spectral noise; and transmission impairment testing (noise, SNR, return loss, crosstalk)
• Automatic testing using scripts, including POTS close out, good pair check, and wideband auto tests.

ADSL is designed to carry a digital signal, over a copper pair, above the voice frequency band (20 KHzﾖ1.1 MHz) to enable high speed internet service over a standard POTS line. This allows ﾓalways onﾔ internet access while simultaneously providing voice service. Typical POTS line quality will normally support ADSL, but the DSL service must be tested when trouble strikes. To troubleshoot DSL service, a modem emulation test set, such as the HST-3000, is needed. The DSLAM and network configuration is verified by connecting at the main distribution frame (MDF) where known interference and attenuation are minimal, as shown in Figure 1. The physical (ADSL) layer data rates and noise margins are reviewed to confirm that they match the service contract. Validate correct DSLAM and BRAS provisioning by connecting to the customer line and authenticating with the network through the DSLAM.

E1/Datacom Service Interface Module (SIM)

ﾕDatacom (X.21, V.24 (RS-232), V.35, V.36 (RS-449), EIA-530)
ﾕG.703: 2 Mbit/s Testing
ﾕ 2 RX/2 TX: E1 Interfaces
ﾕ Bulk, n x 64 kbit/s BERT
ﾕG.821, G.826, M.2100
ﾕ Audio Monitor
ﾕ Signal Level and Frequency
ﾕ Round Trip Delay
ﾕ Event Log and Histograms
ﾕ Pulse Shape
ﾕ Frame Relay

The JDSU HST-3000 E1/Datacom Service Interface Module (SIM) delivers the full functionality required for technicians tasked with ensuring and delivering high quality of service (QoS) for E1/Datacom. Part of a comprehensive catalog of modules for the HST-3000 platform, the E1/Datacom SIM provides the complete range of installation, maintenance, and troubleshooting features needed for E1/ Datacom circuits and network elements.

10/100/1000 Ethernet Service Interface Module (SIM)

• Supports Electrical and Optical Ethernet testing in a single module
• Performs traffic generation up to interface line rate and supports automated RFC2544 at Layers 2 to 4 (Eth/IP/TCP/UDP)
• Layer 2/3/4 multiple streams option facilitates Class of Service testing
• New J-Proof testing generates and analyzes a wide variety of control plane messages to verify proper switching and routing through transparent Ethernet networks
• Enables Ethernet OAM, PBB/PBT, MPLS, VLAN, QinQ, and IP testing
• IPv6 option enables installation and troubleshooting of IPv6 networks
• Dual-port ﾑThru Modeﾒ configuration enables live traffic analysis
• PPPoE protocol support for emulation of data traffic in the last mile
• Simplified user interface facilitates ease-of-use and minimizes techniciansﾒ learning curves
• Supports VoIP and IP Video testing

IPv6 features an auto-configuration facility, defined in RFC2461, which greatly simplifies address configuration. In ﾓstatelessﾔ mode, an IPv6 host will automatically configure itself with a unique link-local address, which enables it to communicate locally on its own subnet. For communication over the Internet, the local router provides the host with a global address. Both transactions are completely transparent to the user, resulting in a truly plug-and-play environment. IPv6 also supports manual address configuration and DHCPv6 using a ﾓstatefulﾔ address configuration when network administrators require tighter control over IP address allocation. The IPv6 option on the HST-3000 Ethernet SIM supports all three configuration schemes for IPv6 traffic testing for 10/100/GigE networks.

The IPv6 option also features Monitor/Thru mode testing in which the HST-3000 gathers and analyzes live IPv4 and IPv6 traffic.



For full JDSU HST-3000C CUADSL2 product specifications, please click here: JDSU HST-3000C CUADSL2

JDSU Acterna HST-3000C HandHeld Consumer Services Tester

Installed Options:
- IP Suite
- Resistive Fault Locator
- Time Domain Reflectometer
- VT100 Emulation
- Wide-Band TIMS

INCLUDED MODULES:
- HST-3000 SIM CUADSL2-TX ANX A Module (Copper, ADSL, & ADSL2 Testing For Annex A)
- JDSU HST-3000 SIM E1/Datacom (Datacom & E1 Circuit Tesing)
- JDSU HST-3000 SIM Ethernet (Optical 10/100/1000 Network Testing)

Includes Carrying Case & Accessories As Listed

HST3000 CUADSL 2 TX ANX A E1 Datacom

JDSU HST-3000C CUADSL2-TX ANX A E1 / Datacom & Ethernet Consumer Services Tester HST3000C CUADSL2-TX ANX A E1 / Datacom & Ethernet Consumer Services Tester Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.

BC# 18652 13236 18772 12339 10459 10456

• JDSU HST-3000C HandHeld Consumer Services Tester (BC# 18652) w/ Option:
  • IP Suite
  • Resistive Fault Locator
  • Time Domain Reflectometer
  • VT100 Emulation
  • Wide-Band TIMS
• JDSU HST-3000 SIM CUADSL2-TX ANX A Module (BC# 18772)
• JDSU HST-3000 SIM E1/Datacom Module (BC# 12339)
• JDSU HST-3000 SIM Ethernet Module (BC# 13236)
• Test Leads Set
• JDSU JSH-4254DB3-HP Transceiver (BC# 10459)
• JDSU JSH-4254DB3-HP Transceiver (BC# 10456)
• (2) Ethernet Cables
• (2) MM LC-LC Duplex Fiber Cables
• (3) International Adapters
• AC Adapter/Charger
• User Manual On CD-ROM
• Carrying Case (G)

Having trouble viewing this file? Click this link to download