| Sensitivity |
50 Ω:1mV/div–1V/div, fully variable1 MΩ:1mV/div–10V/div, fully variable |
| DC Gain Accuracy (Gain Component of DC Accuracy |
±(0.5%)F.S,off set at 0V |
| Bandwidth Limiters |
20MHz, 200MHz |
| Maximum Input Voltage |
50 Ω:5Vrms,1MΩ: 400V max (DC+PeakAC≤10Khz) |
| Input Coupling |
50 Ω:DC, GND;1MΩ:AC, DC, GND; |
| Input Impedance |
50 Ω±2.0%;1MΩ±2.0%||15pF, |
| Offset Range |
50 Ω:1mV-4.95mV:±1.6V,5mV-9.9mV:±4V,10mV-19.8mV:±8V,20mV-1V:±10V1 MΩ: 1mV-4.95mV:±1.6V,5mV-9.9mV:±4V,10mV-19.8mV:±8V,20mV-100mV:±16V, 102mV-198mV:±80V,200mV-1V:±160V,1.02V-10V:±400V |
| DC Vertical Offset Accuracy |
±(1.0% of offset value +0.5%FS+0.02% of max offset+1mV |
| Analog - Acquisition |
|
| Sample Rate (Single-shot) |
2.5GS/s |
| Sample Rate (Repetitive) |
125GS/s,user selectable for repetitive signals (20ps/divto10ns/div |
| Record Length |
Standard-STD:50Mpts/ch(all channels)
Option-L:100Mpts/ch(all channels)
Option-XL:250Mpts/ch(all channels) |
| Acquisition Modes |
Real-time,Roll,RIS(Random Interleaved Sampling),Sequence(Segmented Memory up to 30,000segments,60,000 segments-LOption, 65,000-XLoption)with 1us intersegment dead-time |
| Timebase Range |
20ps/div-5ks/div with standard memory (up to 10ks/div with-L memory,25ks/div with-XL memory);RIS available at ≤ 10ns/div;Roll Mode available at ≥100ms/div and≤5MS/s |
| Timebase Accuracy |
±2.5ppm for 5 to 40C+1.0ppm/year from calibration |
| Channel-Channel Deskew Range |
±9x time/div.setting,100ms max.,each channel |
| External Timebase Reference (Input) |
10 MHz ±25 ppm at 0 to10dB min to 50Ω |
| External Timebase Reference (Output) |
10MHz2.0dBm±1dBm,sine wave synchronous to scope timebase |
| External Clock |
DCto100MHz;(50Ω/1MΩ), ext.BNC input,Minimum rise time and amplitude requirements apply at low frequencies |
| Analog - Acquisition Processing |
|
| Averaging |
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps |
| Enhanced Resolution (ERES) |
From 12.5- to 15-bits vertical resolution |
| Envelope (Extrema) |
Envelope, floor, or roof for up to 1 million sweeps |
| Interpolation |
Linear (Default) or Sinx/X |
| Triggering System |
|
| Modes |
Auto, Normal, Single, Stop |
| Sources |
Any input channel, External, Ext/10, orline; slope and level unique to each source (except for line trigger) |
| Coupling |
DC, AC, HFREJ, LFREJ |
| Pre-trigger Delay |
0-100% of memory size |
| Post-trigger Delay |
0-10,000 Divisions in real time mode, limited at slower time/div settings or in roll mode |
| Hold-off |
From 2ns up to 20s or from 1 to 99,999,999 events |
| Internal Trigger Level Range |
±4.1 div from center (typical |
| External Trigger Input Range |
Ext: ±400mV, Ext/10: ±4V |
| Maximum Trigger Rate |
1M Triggers/sec (in Sequence Mode, up to 4 channels) |
| Trigger Sensitivity with Edge Trigger (Ch1–4 |
0.9 division: 10 MHz
1.0 divisions: 200 MHz
1.5 divisions: 250 MHz
2.0 divisions: 500 MHz |
| External Trigger Sensitivity, (Edge Trigger) |
0.9 division: 10 MHz
1.0 divisions: 200 MHz
1.5 divisions: 250 MHz
2.0 divisions: 500 MHz |
| Max.Trigger Frequency,(C1-C4,Aux In,Smart Trigger) |
500 MHz |
| Trigger and Interpolator Jitter |
≤3.5 ps rms (typical) <0.1 ps rms (typical, software assisted) |
| Trigger Types |
|
| Edge |
Triggers when signal meets slope (positive, negative, or either)and level condition |
| Width (Signal or Pattern) |
Triggers on positive or negative glitches with selectable widths selectable as low as 200ps (depending on oscilloscope bandwidth) ; Maximum Width: 20s |
| Pattern |
Logic combination (AND ,NAND, OR, NOR) of 5 inputs(4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently.Triggers at start or end of the pattern |
| Measurement Trigger |
Trigger on Measurement with qualified limits. |
| TV-Composite Video |
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50or60Hz) and Line; or CUSTOM with selectable Fields (1–8), Lines (upto2000), Frame Rates (25,30,50,or60Hz), Interlacing (1:1,2:1,4:1,8:1), or Synch Pulse Slope (Positive or Negative) |
| Smart Triggers |
|
| Window |
Triggers when signal exits a window defined by adjustable thresholds |
| Interval (Signal or Pattern) |
Triggers on intervals selectable between 1ns and 20s |
| Glitch |
Triggers on positive or negative glitches with widths selectable as low as 200ps (depending on oscilloscope band-width)to 20s, or on intermittent faults |
| Dropout |
Triggers if signal drops out for longer than selected time between 1ns and 20s |
| Runt |
Trigger on positive or negative runts defined by two voltage limits and two time limits.Select between 1ns and 20ns |
| Slew Rate |
Trigger on edge rates. Select limits ford V, dt, and slope. Select edge limits between 1ns and 20ns |
| Multi-Stage Triggers |
|
| Cascade (Sequence) Triggering |
|
| Capability |
Armon“A”event, then Trigger on“B”event.Or Armon“A”event, then Qualify on“B”event, and Trigger on“C”event.Or Armon“A”event, then Qualify on“B”then“C”event, and Trigger on“D”event |
| Types |
A,B,C, or Devent: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate,Pattern (analog), or Measurement. |
| Holdoff |
Hold off between A and B, Band C, C or D, or any is selectable by time or number of events |
| Qualified First |
In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Hold off between sources is selectable by time or events |
| Qualified |
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events |
| Triggerscan |
A Trigger Trainer analyzes the wave forms, identifies normal behavior, and then sets up alarge set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
| Triggers with Exclusion Technology |
Glitch, Width, Interval, Runt, SlewRate-Trigger on intermittent faults by specifying the expected behavior and trig-gering when that condition is not met |
| Measurement Tools |
|
| Measurement Functionality |
Display any 8 parameters together with statistics, including their average, high, low, and standard deviations. Histicons provide a fast, dynamic view of parameters and wave shape characteristics. Parameter Math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location on the source waveform. Each occurrence of each parameter is measured and added to the statistics table. |
| Measurement Parameters |
Amplitude, Area, Base (Low), Cycles, Data, Delay, Delta Delay,Duty Cycle, Duration, Fall time (90–10%,80–20%,@level), Frequency, First, Last, Level @x, Maximum, Mean, Median, Minimum, Narrow band phase, Narrow band power, Number of points, +Overshoot, –Overshoot, Peak-to-peak, Period, Risetime (10–90%,20–80%,@level), RMS, Std.deviation, Top, Width, Median, Phase, Time @ minimum (min.), Time @ maximum (max.), Delta time @ level, Delta time @ level from trigger, X @max., X @min., Cycle-Cycle Jitter, N-Cycle, N-Cycle with start selection, Frequency @ level, Period @ level, Half Period, Width @level, Time Interval Error @ level, Setup, Hold, Skew, Duty Cycle @ level, Duty Cycle Error, Edge @ lv(countsedges) |
| Math Tools |
|
| Math Functionality |
Display up to 8 math function traces (F1–F8).The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
| Math Operators |
Absolute value, Average (summed), Average (continuous), Correlation (two waveforms), Cubic interpolation, Derivative, Deskew (resample), Difference (–), Enhanced resolution (to15bitsvertical), Envelope, Exp(base), Exp(base10), FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared, up to 128Mpts and rectangular, VonHann, Hamming, Flat To pad Blackman Harris windows), Floor, Integral, Interpolate (cubic, quadratic, sinx/x), Invert (negate) ,Log (basee),Log (base10), Product(x), Reciprocal, Rescale (with units), Roof, (SINx)/x,Sparse, Square, Square root, Sum(+), Zoom (identity). 2 dual operator math functions may be defined at a time |
| Measurement and Math Integration |
|
| |
Histograms expanded with 19 histogram parameters and up to 2 billion events Trend(data log)of up to 1 million events Track graphs of all parameters Persistence histogram, persistence trace (mean,range,sigma) |
| Pass/Fail Testing |
|
| Test Types |
Parameter limit testing, mask testing. Pass/Fail Actions include: Save, Stop, Alarm, Pulse, Hardcopy, LabNotebook) |
| Probes |
|
| Standard Probes |
PP018 (5 mm) (Qty. 4) |
| Probing System |
BNC and Teledyne LeCroy Pro Bus for Active voltage, current and differential probes |
| Display System |
|
| Display Size |
Color 12.1" wide screen flat panel TFT-Active Matrix with high resolution touch screen |
| Display Resolution |
WXGA; 1280 x 800 pixels |
| Number of Traced |
Display a maximum of 16 traces. Simultaneously display channel, zoom, memory and math traces |
| Grid Styles |
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quattro, Twelve, Sixteen |
| Waveform Representation |
Sample dots joined, or sample dots only |
| Connectivity |
|
| Ethernet Port |
(2)10/100/1000 Base-T Ethernet interface (RJ-45connector) |
| USB Host Ports |
(6) USB Ports Total–(2) Front USB Ports |
| USB Device Port |
(1)USBTMC Port |
| GPIB Port (Optional) |
Supports IEEE – 488.2 (External) |
| External Monitor Port |
Standard 15-pin D-Type SVGA-compatible DB-15 connector, DVI connector and HDMI connector |
| Remote Control |
Via Windows Automation, orvia Teledyne LeCroy Remote Command Set |
| Processor/CPU |
|
| Type |
Intel Core i5, 2.5GHz (or better) |
| Processor Memory |
8 GB standard |
| Operating System |
Windows® Embedded Standard 7 Professional, 64-bit |
| Power Requirements |
|
| Voltage |
100–240 VAC ±10% at 45–66Hz; 100–120VAC ±10% at380–420Hz; Automatic AC Voltage Selection; Installation Category: 300 V CAT II |
| Power Consumption (Nominal) |
200W / 200V |
| Max Power Consumption |
350 W / 350 VA(with all PC peripherals and active probes connected to 4 channels) |
| Environmental |
|
| Temperature |
Operating: 5°C to 40°C; Non-Operating:-20°C to 60°C |
| Humidity |
Operating: 5% to 90% relative humidity (non-condensing) up to +31°C, Upper limit deratesto 50% relative humidity (non-condensing) at+40°C; Non-Operating: 5% to 95% relative humidity (non-condensing)as tested per MIL-PRF-28800F |
| Altitude |
Operating: 3,048m (10,000ft) maxat ≤30C; Non-Operating: Up to 12,192 meters (40,000ft) |
| Random Vibration |
Operating : 0.31 grms 5Hz to 500Hz, 15 minutes in each of three orthogonal axes; Non-Operating: 2.4 grms 5Hz to 500Hz, 15 minutes in each of three orthogonal axes |
| Functional Shock |
30 g peak, half sine,11ms pulse,3 shocks (positive and negative)in each of three orthogonal axes,18 shock stotal |
|
|
