NetAlly Linkrunner 10G Pro Ethernet Tester
Condition: Refurbished / Calibrated
Warranty: 1 YEAR WARRANTY
Shipping: USA & Worldwide
- NetAlly Linkrunner 10G Pro Ethernet Tester
The LinkRunner 10G Pro is a high-performance solution for Multi-Gig and 10 Gig network testing. LinkRunner 10G simplifies testing and configuration of copper and fiber Ethernet networks, streamlining workflows by combining essential functions of installation and triage in a single, ruggedized unit.
This next-generation tester delivers complete network validation and troubleshooting at linerate from the media (copper/fiber) to the application (layers 1 – 7), accelerating deployments, speeding problem identification, and improving the efficiency and effectiveness of network installers and operations teams.
• Install, test, verify, and troubleshoot technology upgrades, Multi-Gig (NBASE-T) and 10G networks with advanced troubleshooting apps and purpose-built test hardware at linerate.
• Physical layer testing includes cable (TDR) testing, toning, wiremapping, and LANBERT Media Qualification testing with cable SNR (Signal-to-Noise Ratio) measurements for Multi-Gig links
• Compatibility with standards compliant SFPs enables test and validation of any wired media (copper or fiber) for a variety of use models
• Validate up to 90W 802.3bt PSE with TruePower loaded Power over Ethernet (PoE) test
• Two LinkRunner 10G units can be used for line-rate performance testing to verify network capacity, performance and QoS, as well as service provider SLAs between sites.
List of Problems Automatically Detected by LinkRunner 10G Pro
- Bad Subnet Mask High Interface Utilization
- High Disk Utilization
- Duplicate IP Address High Interface Errors
- High Memory Utilization
- DHCP Server Not Responding
- High FCS Errors Recent Device Reboot
- LinkRunner 10G Pro Received Used IP from DHCP
- High Packet Discards
- Spanning Tree Topology Change
- LinkRunner 10G Pro Lost DHCP Lease Detected Half-Duplex Interfaces
- SNMPv3 Agent Responded to SNMPv1/v2 Query
- Max Clients on SSID
- High CPU Utilization
Specifications:
| Battery | Rechargeable lithium-ion battery pack (7.2 V, 6.4 A, 46 Wh) |
| Battery life | Typical operating life is 3-4 hours (Battery life from full charge varies depending on the feature being used); Typical charge time is 3 hours |
| Display | 5.0-inch color LCD with capacitive touchscreen (720 x 1280 pixels) |
| Host interfaces | RJ-45 and SFP Analysis ports RJ-45 Cable Test and Management Port USB Type-A Port and USB Type-C On-the-Go Port |
| Memory | Approximately 8 GB available for storing test results and user applications |
| Supported IEEE Standards |
Wired: 802.3/ab/ae/an/bz/i/u/z PoE: 802.3af/at/bt, Class 0-8 and UPOE |
| Charging |
USB Type-C 65-W adapter: AC Input Power 100-240 V, 50-60 Hz; DC Output Power 15 V (3 A) |
| Operating Temperature |
32°F to 113°F (0°C to +45°C) NOTE: The battery will not charge if the internal temperature of the device is above 122°F (50°C). |
| Operating relative humidity (% RH without condensation) |
90% (50°F to 95°F; 10°C to 35°C) 75% (95°F to 113°F; 35°C to 45°C) |
| Storage temperature | -4°F to 140°F (-20°C to +60°C) |
Sell Your Equipment
At AAATesters we are committed to helping you maximize the value of your surplus, excess and underutilized Test Equipment. We buy Test Equipment of all makes and models.
If you would like to Sell your Equipment, please submit the Request form below.
Reasons to Sell to Us
• Quick & Easy Process to Sell or Trade Equipment
• Get Cash Today! or Trade-in Credit for New or Refurbished Equipment
• Free Shipping - We will Pay for Shipping to us. We can even setup, pack and pickup the Equipment you are selling to us
• Improve ROI, Operational Efficiency, Budget Management, and Planning of your Future Needs