Tektronix THS3014 100MHz Handheld Oscilloscope

 Tektronix THS3014 100MHz Four Channel Oscilloscope
With 4 isolated channels and up to 7 hours of battery life, the lightweight THS3000 Handheld Oscilloscope Series enables you to safely make floating or differential measurements on your bench or in the field. Now you can tackle tough environments with the performance you expect from Tektronix - safely and affordably.

Accurately measure your signals
With up to 100 MHz bandwidth, 4 channels, and 2.5 GS/s maximum sample rate, no other oscilloscope offers as much bandwidth and sample rate in a portable handheld form factor. The THS3014 Handheld Oscilloscope Series has 10,000 points record length per channel, enabling you to capture more signal information at higher sample rates to clearly see signal details. For applications where it is important to measure slow-changing signals over long time periods, the THS3000 Series offers Roll mode that extends the record length to 30,000 points of signal information.

Safely make floating and differential measurements
Making accurate and safe measurements on power electronics, power semiconductors, and other electronics applications can be challenging when the signal reference is floating and not referenced to earth ground. When your signal ranges from low voltage to high voltage (kV) or you must use probing techniques that can potentially create ground loops, the problem is compounded.

To enable floating measurements, the THS3000 Series is architecturally different than most other oscilloscopes. All input channels are fully isolated from the main chassis and from each other. Additionally the power adapter and USB interface are fully isolated to ensure safe measurements and eliminate the risk of unintentional grounding or accidental short circuits. When configured with the proper probes you can be assured you'll be able to make quick, safe, and accurate measurements.

Fast analysis of your device
The THS3000 Handheld Oscilloscope Series is packed with analysis tools to help you validate your device's operation and identify issues quickly. With waveform math, you can add, subtract, or multiply any of your signals to investigate instantaneous power or look at gain. Vertical and horizontal cursors allow you to look at a specific point on your waveform for accurate measurements of voltage, current, time, or frequency. With 21 automated measurements, you can make common measurements quickly and accurately. The built-in Fast Fourier Transform (FFT) function allows you to see the frequency spectrum of your signal, revealing signal interference, crosstalk, or switching noise.

Find intermittent faults with TrendPlotﾙ
Intermittent faults can be caused by timing errors, temperature changes, environmental influences, or simply broken wiring or connectors. The TrendPlotﾙ function helps you find those faults by plotting minimum and maximum measurement values over time. You can select up to 4 measurements and plot any combination of voltages, amps, frequency, time, and phase for any or all four inputs, all with time capture information.

Waveform limit testing
The THS3000 Series can automatically monitor your signals and output Pass or Fail results by judging whether the input waveform is within predefined boundaries. User selections can include testing one or all input channels and automatic recording of Pass or Fail data. Data can easily be reviewed using the Replay mode or stored externally to a USB memory device.

Automatic capture and data logging of 100 display screens
Capturing random or changing signals can often be difficult. The THS3000 Series greatly simplifies any type of waveform data logging by continuously capturing 100 display screens. Each screen capture can include multiple channels and math waveforms, each with its own time stamp. Data capture can also be tailored to specific events by selection of qualified trigger conditions. Playback is quick and easy with the automatic replay of all captured screens or only the screens you select.

Complete solution for power measurements
For performing power measurement on motor drives, power converters/inverters, and power semiconductor devices the THS3000 Series is equipped to handle most common measurements. For basic debugging, the isolated input channels can be used with a variety of voltage and current probes. Each input channel can be configured to match the probe type and attenuation ensuring correct measurements and cursor readings. Four channels allow for easy measurements of three-phase power or simultaneous capture of digital control and power signals.

Measurements on power conversion electronics usually require probes with higher voltage ratings. Tektronix offers a passive probe with insulation systems specifically designed for making floating measurements. The THP0301-X can measure up to 849 Vp-p (300 VRMS). Optional P5122 probes, when coupled with the THS3000 Series, are suitable for making measurements on 1000 VRMS devices in Category II environments, with a maximum float voltage of up to 600 VRMS relative to earth ground.

Intuitive operation
The THS3000 Handheld Oscilloscope Series has a front-panel layout and an intuitive user interface which makes the instrument easy to use, reducing learning time and increasing efficiency. For initial setup or for situations where you're constantly changing connection points, the THS3000 Series has a single-button Autoset and Autorange feature which can automatically set up the trigger system and adjust vertical and/or horizontal oscilloscope settings.

Easy to use
The bright color display makes it easy for you to see the signals you're measuring. Each waveform is color coded and designed to correspond to the colors on the input probe connectors, the front-panel channel selector buttons, and the individual probes which are colored at both ends. By matching the colors during setup you'll be assured you can easily identify your waveforms.

For setup assistance user messages are available in 11 user-selectable languages including English, French, German, Spanish, Portuguese, Italian, Japanese, Simplified and Traditional Chinese, Korean, and Russian.

Features:

• 21 automatic measurements
• Waveform math and FFT spectral analysis
• Volts, time, frequency, watts cursor measurements
• Measurement data logging with TrendPlotﾙ
• Waveform pass/fail limit testing
• Automatic 100 display screens recorder
• 6 in. (153 mm) bright color display
• USB device and host support
• 7 hours of continuous battery operation

Applications:

• Embedded analog and digital design
• Power devices, power electronics, and power supply design
• Automotive and avionics design and maintenance
• Industrial equipment design and installation
• Field test and service

Specifications:

Isolated input channels	4
Analog bandwidth (-3 dB)	100 MHz
Rise time	3.5 ns
Hardware bandwidth limits	20kHz, 20 MHz, or full
Float voltage	1000 VRMS CAT II / 600 VRMS CAT III from BNC shell to earth ground
Maximum sample rate	2.5 GS/s (1.25 GS/s 4-ch)
Maximum record length (all channels)	10,000 points (30,000 points in roll mode (4 ms to 2 min / div))
Vertical system
Input coupling	AC, DC
Input impedance	1 MO ±1%, 14 pF ±2 pF
Input sensitivity range	2 mV/div to 100 v/div
Vertical resolution	8 bits
DC gain accuracy	±2.1% of reading +0.04 × range/div for 5 mV/div to 100 V/div
Max BNC input voltage	(1 MO) 300 VRMS CAT III from BNC signal to BNC shell
Max probe voltage (with THP0301-X probe)	300 VRMS CAT III from 10:1 probe tip signal to BNC and reference lead
Trace positioning	±4 divisions
Horizontal system
Time base range (s/div)	2 ns to 4 s
Delay time range	1 full screen (12 divisions) of pre-trigger or up to 100 screens (1,200 divisions) of post-trigger
Timing accuracy	±100 ppm + 0.04 div
Zoom	Horizontally expand or compress a live or stopped waveform
Trigger system
Input source	Channel 1, 2, 3, or 4. All input references isolated from each other and earth ground
Main trigger modes	Auto-level, Auto, Normal, and Single
Trigger coupling	DC, HF reject, Noise reject (reduces sensitivity)
Trigger sensitivity, internal DC coupled	0.5 divisions from DC to 5 MHz at >5 mV/div 1 divisions >5 MHz to 100 MHz
Trigger level range	±4.0 divisions
Trigger modes Edge Pulse width	Positive, negative, or dual slope on any input channel. Coupling includes DC, HF reject, and Noise reject Trigger on channel 1, width of positive or negative pulses (glitches) that are >, <, =, or ? a specified period of time (resolution of 0.01 div with minimum time of 50 ns)
Event	Trigger on n-th occurrence of trigger (N selectable from 2 to 99)
Video	Trigger on channel 1, line number, all lines, odd, even, or all fields on NTSC, PAL, PAL plus, and SECAM signals
Non-interlaced	Trigger on channel 1, high-res non-interlaced video with line frequencies from 14 kHz to 65 kHz
Acquisition modes
Sample (default)	Acquire sampled values
Glitch detect	Captures high frequency or glitches as narrow as 8 ns from 5 µs to 120 s / div
Averaging	Selectable from 2, 4, 8, or 64 waveforms
Roll	Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 4 ms/div
Data recorder	Automatic data logging of 100 triggered records (screens) with date and time stamp. store internally or to a USB device
Waveform compare	Visually compare against user-definable reference waveforms or perform automatic pass or fail testing of 1 to 4 channels with data logging of test results
Automatic setup
Autoset	Single-button, automatic setup of all channels for vertical, horizontal, and trigger systems
Autorange	Continuous auto-setup of vertical, horizontal, and trigger systems that track signal changes
Waveform measurements
Cursors	Time, freq (1/T), volts, watts, Rise/Fall time from any input channel or math waveform
Automatic measurements	21. Up to 4 can be displayed on-screen at any one time. Measurements include: V DC, V ACRMS, V AC+DC, VPeak Max, VPeak Min, Peak to Peak, A DC, A AC, A AC+DC, Frequency, Rise time (using cursors), Fall time (using cursors), Phase (between any 2 inputs), Positive pulse width, Negative pulse width, Positive duty cycle, Negative duty cycle, dBV, dBm into 50 O and 600 O
TrendPlotﾙ	Records and graphically displays any 4 automatic scope measurements. store internally or to USB flash drive for recall and analysis
Waveform math
Arithmetic	Add, subtract, and multiply waveforms
FFT	Spectral magnitude. Set FFT vertical scale to Linear or Logarithmic, and FFT window to Automatic, Hamming, Hanning, or None
Display system
Display type	6 in. (153 mm) liquid-crystal color display
Display resolution	320 horizontal × 240 vertical pixels
Waveform style	Vectors (dot-join), Dots, Envelope, Variable persistence, Infinite persistence
Display format	YT and XY
Storage memory
Reference	4 user-definable reference traces
Waveform	Stores 30 internal scope records (4 traces each) with screen image and corresponding setup
Recording	Store 10 internal recordings that can be a 100-screen replay sequence, a roll-mode recording, or a TrendPlotﾙ measurement recording
Screen image	Store up to 9 internally or 256 BMP images to an external USB storage drive
Real-time clock	Time and date stamp of all stored data
Input/Output ports
USB host port	Supports USB mass storage devices
USB device port	Mini-USB-B connector allows for communication/control of oscilloscope
Probe compensator output Amplitude Frequency	Side-panel output ﾖ 1.225 Vp-p 500 Hz
Kensignton-style lock	Side-panel security slot connects to standard Kensington-style lock
Power source
Battery	7 hour, 10.8 v rechargeable Li-Ion battery
Battery charging time	5 hours
Line power	AC power adapter/charger
Power source voltage	100 v to 240 v AC ±10%
Power source frequency	50 hz to 60 hz
Physical characteristics
Dimension Height Width Depth	265 mm (10.5 in.) 190 mm (7.5 in.) 70 mm (2.8 in.)
Weight Net Shipping (base model) Shipping (TK model)	2.2 kg (4.8 lb.) 4.7 kg (10.4 lb.) 7.8 kg (17.1 lb.)
Environmental
Enclosure	IP 41 according to IEC60529S
Temperature Operating Nonoperating	0 °C to +40 °C (with battery) 0 °C to +50 °C (without battery) ﾖ20 °C to +60 °C
Humidity Operating Nonoperating	0 °C to 10 °C, noncondensing 10 °C to 30 °C, up to 95% relative humidity 30 °C to 40 °C, up to 75% relative humidity 40 °C to 50 °C, up to 45% relative humidity ﾖ20 °C to 60 °C, relative humidity, noncondensing
Altitude Operating Nonoperating	Up to 3,000 m (9,843 ft.) Up to 12,000 m (39,370 ft.)
Vibration/Shock Operating Nonoperating	Vibration (Sinusoidal): 3 g max, according to MIL-PRF-28800F, class 2 Shock: 30 g max, according to MIL-PRF-28800F, class 2 Vibration (Random): 0.03 g2/Hz, according to MIL-PRF-28800F, class 2
Regulatory Electromagnetic compatibility Safety	EN 61326-1:2006, EN 61326-2-1:2006 for emission and immunity UL61010-1:2004; CAN/CSA C22.2 No. 61010.1-04; EN61010-1:2001, Pollution degree 2; ANSI/ISA-82.02.01

For full Tektronix THS3014 product specifications, please click here: Tektronix THS3014

Having trouble viewing this file? Click this link to download