Keysight Agilent E5063A 8.5GHz ENA Vector Network Analyzer w/ Opts 019 & 285
Condition: Refurbished / Calibrated
Warranty: 1 Year Warranty
Shipping: USA & Worldwide
- Keysight Agilent E5063A 8.5GHz ENA Vector Network Analyzer w/ Options: (BC# -L/T*)
- Option 019: Standard Storage Drive
- Option 285: 2-port test set, 100 kHz to 8.5 GHz
- Option 019: Standard Storage Drive
- Power Cord
- User Manual on CD
Keysight Agilent E5063A 8.5GHz ENA Vector Network Analyzer
The Best Balance Between Price and Performance
The Keysight E5063A ENA is an affordable bench top vector network analyzer (VNA) for testing simple passive components such as antennas, filters, cables or connectors up to 18 GHz. The E5063A provides the best balance between price and performance to satisfy your business and technical requirements. It leverages the consistent measurement framework of the industry standard ENA Series to boost efficiency and productivity, and is future proof and ready to evolve as the technologies change.
DUT examples
Antennas for smartphones, cellular base stations, WLAN, and other wireless communication devices
Other simple RF passive components such as filters, cables, connectors, attenuators, couplers, isolators, and dividers
Impedance test of PC board (PCB)
Wireless power transfer coils/resonators
Dielectric materials
Drive Down The Cost of Test for RF Passive Components
Solid performance at an affordable price
The E5063A delivers a great combination of performance, accuracy and repeatability all at an affordable price. The E5063A is a safe investment to lower your total cost of ownership.
Trace noise (0.002 dBrms1) and stability (0.01 dB/°C2)
The best-in-class performance comparable to higher-end ENA models
Enables accurate measurements of low-loss devices
Dynamic range (maximum 122 dB3)
Satisfies test requirements of simple RF passive components.
You can choose the best suited frequency range from 8 different frequency options (500 M/1.5 G/3 G/4.5 G/6.5 G/8.5 G/14 G/18 GHz) depending on your test needs and budgets. In addition, the frequency upgradability allows you to start your investment with the lower-priced 500 MHz option and later upgrade it to higher frequency options up to 18 GHz options when necessary. Optimize your investment for your current and future needs with the E5063A
Ready for Production Testing
Proven calibration and analysis capabilities
The E5063A fully supports major calibration and data analysis capabilities that are compatible with the E5071C and required for testing RF passive components. With these proven capabilities, the E5063A provides measurements consistent with the industry standard E5071C.
Calibration capabilities
SOLT cal (with known thru, or unknown thru)
Adapter removal/insertion
ECal (Electronic Calibration)
TRL cal
Fixture simulator
Virtual matching circuit embedding
De-embedding
Port-Z conversion
1-port mixed-mode S-parameters
Data analysis
Equation editor
Point limit (for antennas)
Ripple & Bandwidth limit (for filters)
Single marker search for max, min, peak, or target value
Multiple marker search for peaks or target values
Improve your productivity with ECal calibration
Keysight offers a variety of calibration kits with different connector types, frequency ranges, or prices. Keysight also offers electronic calibration (ECal) modules. The ECal is a solid-state device with programmable, and repeatable impedance states, and requires only one set of connections to perform a calibration. Therefore it greatly improves your productivity and minimizes operator’s error.
The Keysight N755xA series is the economy 2-port ECal family equipped with either Type-N or 3.5 mm connectors which offers the convenience of an ECal at a lower price point. The N755xA is supported by the E5063A with the firmware revision A.03.72 or above to lower your cost of ownership.
E5063A ENA Series PCB Analyzer
The best solution for PCB manufacturing test
As the operating speed of electronic circuits increase, signal integrity of printed circuit boards (PCBs) drastically affects performance and there is an increasing requirement for controlled impedance PCBs. In addition, with the proliferation of wireless devices, such as smartphones and tablets, there is a trend to integrate antennas onto PCBs. Therefore, in addition to the traditional time domain impedance measurement, there is a growing need to measure the frequency domain response of PCB integrated antennas.
The E5063A PCB Analyzer requires the E5063A Option 011 (Time domain analysis/Test Wizard). The E5063A provides frequency domain measurement capability and Option 011 adds time domain analysis capability, as well as a dedicated graphical user interface for PCB manufacturing test
Compared to traditional solutions based on sampling oscilloscopes, the E5063A PCB Analyzer provides three breakthroughs for PCB manufacturing test:
More Accuracy and R&R (Repeatability & Reproducibility)
More Languages Supported
More ESD Robustness
More accuracy and R&R
Delivers new standards in speed and accuracy
Low noise floor for accurate and repeatable measurements
State of the art error correction techniques enables you to measure your device, not your measurement system
Fast measurement speed for improved throughput
More languages supported
An analyzer that speaks the user’s language
Since there are many cases where tasks are solved more efficiently in one’s native language, a multi-lingual interface is provided with the graphical user interface.
Currently available languages include English, Simplified and Traditional Chinese, Japanese, and Korean
More ESD robustness
Protection circuits implemented inside the instrument
Proprietary electrostatic discharge (ESD) protection chip significantly increases ESD robustness, while at the same time maintaining excellent RF performance
Highly robust architecture can minimize instrument failure from ESD and free you from worrying about instrument repair fees and downtime
| E5063A key specs & features | |
| Frequency | 100 kHz to 500M/1.5 G/3 G/4.5 G/6.5 G/8.5 G/14 G/18 GHz(settable down to 50 kHz) |
| Test port | 2-port S-parameter, 50 Ω |
| Dynamic range | 117 dB (spec), 122 dB (typical)(at 100 MHz to 4.35 GHz) |
| Trace noise | 0.005 dBrms (spec), 0.002 dBrms (typical), (at 8 M to 4.35 GHz, IFBW = 70 kHz, transmission measurement) |
| Stability | 0.01 dB/°C (at 300 kHz to 6 GHz) |
| Source power | –20 to 0 dBm (at 300 kHz to 8.5 GHz) |
| Sweep type | Linear and log frequency, Segment |
| NOP | Max. 10,001 |
| Channel | Max. 32 |
| Measurement parameters | S-parameters (single-ended, mixed-mode), TDR and single-ended TDT parameters(1), Wireless power transfer efficiency(1) |
| Calibration capabilities | SOLT, Adapter removal/insertion, ECal, TRL, Unknown thru, Waveguide |
| Other major capabilities | Time domain/Test Wizard1, Wireless power transfer analysis1, Limit test (Limit line, Ripple limit, Bandwidth limit, Point limit), Fixture simulator, Equation editor, U1810B/U1816A/C USB switch support |
| (1) Optional capabilities |
For full Agilent E5063A Network Analyzer product specifications, please click here: E5063A